Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › 2017.09–2020.08
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319550 HYBRID VEHICLE TRANSAXLE A

P710 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1.INSTALL STUD BOLT

a.

Using a E10 "TORX" socket wrench, install the 2 stud bolts to the hybrid vehicle transaxle assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 2.INSTALL TRANSAXLE HOUSING PLUG

a.

Install the transaxle housing plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 4 bolts.

C379405N01
1.031,0.698 1.188,0.896 0.156,0.198 10 true A 2.594,1.271 2.75,1.469 0.156,0.198 10 true B 4.552,0.854 4.708,1.052 0.156,0.198 10 true A 4.896,1.552 5.052,1.75 0.156,0.198 10 true A

Torque:
Bolt (A) : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 82125 4.INSTALL TRANSMISSION WIRE

a.

Install the transmission wire to the hybrid vehicle transaxle assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the connector.


Hide 44781E 5.INSTALL HOSE BRACKET

a.
C379403N01
1.031,1.677 1.188,1.875 0.156,0.198 10 true 1 1.417,1.729 1.573,1.927 0.156,0.198 10 true 2

Temporarily install the hose bracket to the hybrid vehicle transaxle assembly with the 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 33823 6.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide G125A 7.INSTALL MOTOR COOLING COOLER

Hide 30900 9.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C379784C01
0.396,0.688 0.594,0.896 0.198,0.208 10 true *1 2.458,0.188 2.667,0.396 0.208,0.208 10 true *1
*1 Knock Pin


Make sure that the knock pins are installed to the engine assembly.


b.
C379785N01
2.75,0.333 2.906,0.531 0.156,0.198 10 true A

Align the knock pins with the holes in the hybrid transaxle assembly and, while keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, temporarily install the bolt (A).

NOTICE:
·

When tightening the bolts, be sure that the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly are in close contact with one another.

·

Do not apply grease to the inner splines of the transmission input damper assembly or input shaft assembly.

·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excessive force when installing the hybrid vehicle transaxle assembly.

·

Make sure to align the hybrid vehicle transaxle assembly so that the input shaft assembly of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper assembly.

·

When inserting the input shaft assembly of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper assembly, do not shake the hybrid vehicle transaxle assembly excessively.

·

When installing the hybrid vehicle transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock pin holes.




c.
C379393N01
2.646,0.427 2.802,0.625 0.156,0.198 10 true A 1.854,0.063 2.01,0.26 0.156,0.198 10 false B 1.021,0.344 1.177,0.542 0.156,0.198 10 true C 2.365,1.958 2.552,2.135 0.188,0.177 10 true D 0.844,1.01 1,1.208 0.156,0.198 10 true C 1.073,1.833 1.229,2.031 0.156,0.198 10 true C 1.802,2.01 1.969,2.177 0.167,0.167 10 true C 2.615,1.75 2.771,1.948 0.156,0.198 10 true C

While keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, install the 8 bolts.

Bolt Bolt Length Torque
(A), (B) 50 mm (1.97 in.) 64 N*m (653 kgf*cm, 47 ft.*lbf)
(C) 45 mm (1.77 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
(D) 35 mm (1.38 in.) 25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 12303 10.INSTALL REAR ENGINE MOUNTING BRACKET

a.
C379392N01
1.417,0.417 1.573,0.615 0.156,0.198 10 true A 0.958,1.698 1.115,1.896 0.156,0.198 10 true B 2.021,1.698 2.177,1.896 0.156,0.198 10 true C 0.99,0.719 1.146,0.917 0.156,0.198 10 true C

Install the rear engine mounting bracket to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (A) → Fully tighten bolt (C)



Hide 12371A 11.INSTALL REAR ENGINE MOUNTING INSULATOR

Hide 12311A 12.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C379391N01
1.104,0.354 1.26,0.552 0.156,0.198 10 true A 2.323,1 2.479,1.198 0.156,0.198 10 true B 1.083,1.396 1.24,1.594 0.156,0.198 10 true C

Install the front engine mounting bracket to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)



Hide 12361A 13.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the front engine mounting insulator to the front engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 51100G 14.INSTALL FRONT FRAME ASSEMBLY

Hide 11363A 15.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the engine assembly.


Hide 28193 16.INSTALL STARTER HOLE INSULATOR

a.

Install the starter hole insulator to the engine assembly with the 2 bolts.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 821H2 17.CONNECT HV AIR CONDITIONING WIRE

a.

Engage the guide to connect the HV air conditioning wire to the hybrid vehicle transaxle assembly.


b.

Install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 82121 18.CONNECT ENGINE WIRE (for LHD)

a.

Install the wire harness to the rack and pinion power steering gear assembly with the 2 bolts.

C375738

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



c.

Connect the 5 clamps.

C388278N01
0.625,2.01 0.781,2.208 0.156,0.198 10 true A 6.417,1.635 6.573,1.833 0.156,0.198 10 true B


d.

Install the 2 bolts.

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82121 19.CONNECT ENGINE WIRE (for RHD)

a.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.

C387932



b.

Connect the 6 clamps.

C379386N01
6.646,1.677 6.802,1.875 0.156,0.198 10 true B 0.594,2.021 0.75,2.219 0.156,0.198 10 true A


c.

Install the 2 bolts.

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 45319 20.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 21.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 22. PERFORM RESOLVER LEARNING

NOTICE:

If the hybrid vehicle transaxle assembly has been replaced, make sure to perform resolver learning.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY