Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE FLUID
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319552 HYBRID TRANSAXLE FLUID N

P710 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE FLUID  ADJUSTMENT  


PROCEDURE

Hide 53851M 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852K 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 5.DRAIN HYBRID TRANSAXLE FLUID

a.
C377438

Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly.


b.
C377439

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly and drain the hybrid transaxle fluid.


c.

Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


d.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



Hide 6.ADD HYBRID TRANSAXLE FLUID

a.
C377440C01
2.385,1.094 2.5,0.823 2.5,0.823 2.635,0.823 false 2.698,0.74 2.938,0.948 0.24,0.208 10 false *a 3.146,1.708 3.375,1.917 0.229,0.208 10 false *b
*a Filler Nozzle
*b 0 to 10 mm (0 to 0.394 in.)


Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly.


b.

Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. [#]

NOTICE:
·

When adding hybrid transaxle fluid, make sure that the vehicle is level.

·

Use Toyota Genuine ATF WS.

·

Be sure to fully insert the filler nozzle into the filler plug opening.

·

Be sure to add hybrid transaxle fluid slowly. If hybrid transaxle fluid is added quickly, the hybrid transaxle fluid may hit internal parts and bounce back, resulting in hybrid transaxle fluid coming out of the filler plug opening.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

Driving the vehicle with an insufficient or excessive amount of hybrid transaxle fluid may damage the hybrid vehicle transaxle assembly.



Hybrid Transaxle Fluid Standard Capacity (for Reference):

3.9 liters (4.1 US qts, 3.4 Imp. qts)



c.

After adding hybrid transaxle fluid, leave the vehicle for 30 seconds so that the hybrid transaxle fluid surface can become still again, and then check that the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. (If the hybrid transaxle fluid level is low, repeat this procedure from step [#].)

NOTICE:

After adding hybrid transaxle fluid, make sure to check the hybrid transaxle fluid level.



d.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



Hide 8.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 9.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 51441 10.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 11.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 12.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH