Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2017.09–2017.12
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324467 ENGINE ASSEMBLY A

A25A-FXS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Perform headlight ECU sub-assembly LH initialization
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.SECURE STEERING WHEEL

Hide 6.REMOVE FRONT WHEELS

Hide 53851M 7.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

a.

Remove the 3 screws and front wheel opening extension pad RH.


Hide 53852K 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

a.

Remove the 3 screws and front wheel opening extension pad LH.


Hide 51441 9.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the bolt, 2 clips, 6 screws and No. 1 engine under cover.


Hide 10.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

a.

Remove the 4 screws, 6 clips and No. 2 engine under cover assembly.


Hide 53737B 11.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 2 screws, clip and front fender apron seal LH.


Hide 53736 12.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 2 screws, clip and front fender apron seal RH.


Hide 52618 14.REMOVE FRONT LOWER BUMPER ABSORBER

a.
A406650

Remove the 4 bolts.


b.

Disengage the 2 claws to remove the front lower bumper absorber.


Hide 15.DRAIN ENGINE COOLANT (for Engine)

Hide 12601B 18.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A406652C02
0.042,0.052 0.344,0.292 0.302,0.24 12 true *A 0.073,2.375 0.375,2.615 0.302,0.24 12 true *B
*A for LHD
*B for RHD


Lift the front of the No. 1 engine cover sub-assembly to disengage the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to disengage the clip and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide G9200 19.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide G92A0A 20.REMOVE INVERTER RESERVE TANK ASSEMBLY

a.
A407618C02
0.51,3.021 0.677,3.021 0.677,3.021 0.948,2.948 true 1.469,3 1.792,2.885 1.792,2.885 1.979,2.885 true 1.104,0.563 1.417,0.563 false 1.219,0.854 1.531,0.854 false 0.25,2.938 0.49,3.135 0.24,0.198 10 true *1 2.021,2.802 2.26,3 0.24,0.198 10 true *2 1.5,0.49 1.74,0.688 0.24,0.198 10 true *a 1.594,0.792 1.833,0.99 0.24,0.198 10 true *b
*1 No. 5 Inverter Cooling Hose
*2 No. 2 Inverter Cooling Hose
*a Pin
*b Grommet


Remove the bolt.


b.

Disengage the pin and remove the inverter reserve tank assembly.


c.

Slide the clip and disconnect the No. 5 inverter cooling hose from the inverter reserve tank assembly.


d.

Slide the clip and disconnect the No. 2 inverter cooling hose from the inverter reserve tank assembly.


Hide 23826 21.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A406653

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve assembly.


Hide 87246 22.DISCONNECT OUTLET HEATER HOSE

a.
A406304C03
1.427,1.51 1.583,1.51 1.583,1.51 1.823,1.271 false 1.229,1.427 1.521,1.667 0.292,0.24 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the outlet heater hose from the No. 2 water by-pass pipe sub-assembly.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater hose connector with plastic bags to prevent damage and contamination.


Hide 87245 23.DISCONNECT INLET HEATER HOSE

a.
A406305C03
1.198,1.563 1.406,1.563 1.406,1.563 1.542,1.167 false 1.01,1.49 1.292,1.698 0.281,0.208 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the inlet heater hose from the flow shutting valve (water by-pass hose assembly).


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater hose connector with plastic bags to prevent damage and contamination.


Hide 23901 24.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A406656

Remove the No. 1 fuel pipe clamp from the fuel tube connector.


b.

Disconnect the fuel tube sub-assembly.

i.
A406657

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 89422 25.REMOVE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR (w/ Canister Pump Module)

Hide 16571C 26.DISCONNECT NO. 1 RADIATOR HOSE (w/o Canister Pump Module)

a.
A406658

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16571C 27.DISCONNECT NO. 1 RADIATOR HOSE (w/ Canister Pump Module)

a.
A407617

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


b.

Remove the bolt to disconnect the No. 1 radiator hose from the front engine mounting bracket.


Hide 16572D 28.DISCONNECT NO. 2 RADIATOR HOSE

a.
A406659

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 88711 29.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 30.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide G9229A 31.DISCONNECT NO. 5 INVERTER COOLING HOSE

a.
A407266

Slide the clip and disconnect the No. 5 inverter cooling hose from the motor cooling cooler.


Hide 32.DISCONNECT WIRE HARNESS

HINT:

After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.


a.
A406661

Remove the No. 2 relay block cover from the engine room relay block and junction block assembly.


b.
A406662

Remove the nut from the engine room relay block and junction block assembly.


c.

Disconnect the 5 connectors from the engine room relay block and junction block assembly.


d.

Using a screwdriver, disengage the claw and disconnect the wire harness from the engine room relay block and junction block assembly.


e.
A406663

Remove the 2 bolts and disengage the earth wire.


Hide 16281F 33.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
A406664

Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.


Hide 45220 34.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 17410 35.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 37.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.




b.
A406665

Remove the 6 bolts and body mounting plate.


c.
A406666

Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


d.
A406668

Remove the 3 bolts and remove the engine mounting stay LH from the engine mounting insulator LH.


e.
A406669

Remove the 4 bolts and separate the engine mounting insulator sub-assembly LH from the hybrid vehicle transaxle assembly.


f.
A406667C03
1.302,2.094 1.458,2.292 0.156,0.198 10 true A 1.313,2.396 1.469,2.594 0.156,0.198 10 true A 1.99,2.083 2.146,2.281 0.156,0.198 10 true A 2,2.396 2.156,2.594 0.156,0.198 10 true A 0.813,0.365 0.969,0.563 0.156,0.198 10 true B 2.417,0.365 2.573,0.563 0.156,0.198 10 true B 1.188,2.781 1.344,2.979 0.156,0.198 10 true C 2.156,2.76 2.313,2.958 0.156,0.198 10 true C 0.729,4.427 0.885,4.625 0.156,0.198 10 true D 2.573,4.458 2.729,4.656 0.156,0.198 10 true D 2.604,3.948 2.76,4.146 0.156,0.198 10 true E 0.708,3.927 0.865,4.125 0.156,0.198 10 true E
V100135

Bolt
V100136

Nut


Remove the 4 bolts (A), 2 bolts (B) and 2 bolts (C) and front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.


g.

Remove the 2 bolts (D), 2 bolts (E) and 2 nuts and front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH from the front frame assembly and vehicle body.


h.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 23825 38.REMOVE FUEL DELIVERY GUARD

a.
A406670

Remove the bolt and fuel delivery guard from the engine mounting bracket RH.


Hide 39.INSTALL ENGINE HANGERS

a.
A406671C02
0.406,0.375 0.563,0.375 0.563,0.375 0.854,0.792 true 2.115,0.292 2.281,0.292 2.281,0.292 2.396,0.49 true 0.208,0.313 0.521,0.51 0.313,0.198 10 false *1 1.854,0.219 2.104,0.427 0.25,0.208 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 11361J 40.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A402190

Remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 45319 41.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 82121 42.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 51100G 43.REMOVE FRONT FRAME ASSEMBLY

Hide 12361A 44.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>REMOVAL

Hide 12371A 45.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A407616

Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.


Hide 821H2 46.REMOVE HV AIR CONDITIONING WIRE

a.
A407269

Disengage the 2 clamps.


b.
A407267C02
1.167,0.563 1.417,0.302 1.417,0.302 1.573,0.302 true 1.625,0.229 1.938,0.427 0.313,0.198 10 false *a
*a Green-colored Lock
V100137

Slide


Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



c.
C379387

Remove the bolt.


d.

Disengage the guide to remove the HV air conditioning wire from the hybrid vehicle transaxle assembly.


Hide 11363A 48.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 30900 49.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 50.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 19315 52.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 53.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 54.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


Hide 12305 55.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A406676

Disengage the No. 6 water by-pass hose.


b.

Remove the bolt, nut and the radiator reserve tank assembly.


c.
A406677

Disengage the clamp.


d.

Remove the bolt and disconnect the cooler bracket from the engine mounting insulator sub-assembly RH.


e.

Remove the 2 bolts and nut and remove the engine mounting insulator sub-assembly RH.


Hide 12341 56.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A406678

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12306 57.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.


a.
A406679

Remove the 2 bolts, nut and the engine mounting insulator sub-assembly LH.