Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2017.09–2019.02
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319558 TRANSMISSION CONTROL CABLE N

P710 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  ADJUSTMENT  


PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
C332327

·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 3.ADJUST SHIFT LEVER POSITION

NOTICE:

Before adjusting the transmission control cable assembly, check that the shift lever position sensor and shift lever are in N.


a.
C380392

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


b.
C194520C31
2.271,2.573 2.615,2.573 false 1.948,1.75 2.083,1.531 2.083,1.531 2.188,1.531 false 1.594,0.958 1.781,1.135 0.188,0.177 10 false *c 1.792,1.344 1.979,1.521 0.188,0.177 10 false *c 2.438,0.781 2.625,0.958 0.188,0.177 10 false *d 2.25,1.458 2.51,1.656 0.26,0.198 10 false *a 2.229,2.313 2.417,2.49 0.188,0.177 10 false *d 2.656,2.49 2.958,2.729 0.302,0.24 10 false *b
*a Slider
*b Lock Piece
*c Slide
*d Pull


Slide the slider of the transmission control cable assembly in the direction indicated by the arrow in the illustration and pull the lock piece outward.


c.
C380403C01
1.167,2.5 1.302,2.5 1.302,2.5 1.406,2.667 false 2.063,2.771 2.177,2.552 2.177,2.552 2.313,2.552 false 1.01,2.406 1.25,2.635 0.24,0.229 10 false *a 2.354,2.448 2.635,2.698 0.281,0.25 10 false *b
*a Lock Piece
*b Adjuster Case


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Check that the lock piece is pulled out.

·

Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.

·

Connect the transmission control cable assembly so that the lock piece faces the driver side.




d.
C296262C01
2.229,0.854 2.365,0.563 2.365,0.563 2.5,0.563 false 1.24,3.219 1.375,2.927 1.375,2.927 1.51,2.927 false 1.208,0.667 1.344,0.375 1.344,0.375 1.479,0.375 false 2.24,3.323 2.375,3.031 2.375,3.031 2.51,3.031 false 1.531,0.281 1.813,0.51 0.281,0.229 10 false *a 1,2.76 1.271,3.01 0.271,0.25 10 false *b 2.552,0.469 2.854,0.698 0.302,0.229 10 false *c 1.552,2.833 1.833,3.063 0.281,0.229 10 false *a 2.542,2.938 2.844,3.167 0.302,0.229 10 false *c
*a Lock Piece
*b Push in
*c Adjuster Case


Push the lock piece into the adjuster case.

NOTICE:
·

Check that the shift lever position sensor and shift lever are in N.

·

Securely push in the lock piece until the slider lock is engaged.




e.

After adjusting the shift lever position, check the position and operation of the shift lever. If there is a problem, adjust the shift lever position again.