Home › Engine / Hybrid System › A25A-FXS (FUEL) › FUEL PUMP (w/o Canister Pump Module)
RM33C0E _51 Engine / Hybrid System _065421 A25A-FXS FUEL _0319775 FUEL PUMP(w/o Canister Pump Module) A

A25A-FXS FUEL  FUEL PUMP(w/o Canister Pump Module)  REASSEMBLY  


PROCEDURE

Hide 23221 1.INSTALL FUEL PUMP

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.

for Type A:

i.
A345414C04
2.323,0.583 2.375,0.427 2.375,0.427 2.531,0.427 false 2.323,0.771 2.677,0.771 false 2.583,0.344 2.896,0.5 0.313,0.156 10 false *1 2.74,0.698 3.052,0.854 0.313,0.156 10 false *2
*1 O-ring
*2 Fuel Pump Spacer


Apply gasoline to a new O-ring. Then install the O-ring and fuel pump spacer to the fuel pump.


ii.

Install the fuel pump to the fuel tube supporter.


iii.

Engage the 3 claws to install the No. 2 fuel suction support to the fuel tube supporter.


iv.

Connect the fuel pump harness connector.


v.
A405226

Engage the claw and clamp to connect the fuel pump harness.

NOTICE:
·

Securely engage the claw.

·

Make sure that there is no foreign matter between the fuel pump and the ground terminal of the fuel pump harness.

·

Make sure that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.




vi.

Check the connection state of the fuel pump harness.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fuel pump body - Ground terminal of the fuel pump harness Always Below 50 Ω


If the result is not as specified, reconnect the fuel pump harness to the fuel pump so that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.


vii.

Engage the 4 claws to install the fuel suction plate sub-assembly to the fuel sub-tank sub-assembly.


viii.
A405231C02
1.813,1.156 1.938,1.156 1.938,1.156 2.135,1.448 true 2.719,1.875 2.552,1.875 2.552,1.875 2.344,1.542 true 1.646,1.073 1.813,1.229 0.167,0.156 10 true *a 2.792,1.802 2.958,1.958 0.167,0.156 10 true *b
*a Protrusion
*b Installation Hole
V100135

Slide


Align the protrusion of the fuel sub-tank sub-assembly with the installation hole of the fuel suction plate sub-assembly and then slide the fuel suction plate sub-assembly to install the fuel sub-tank sub-assembly.


ix.

Connect the 2 fuel pump harness connectors.


x.

Install the harness protector to the wire harness.


xi.

Engage the 2 clamps to connect the fuel pump harness to the fuel suction plate sub-assembly.

NOTICE:
·

Do not damage the wire harness.

·

When engaging each wire harness to the clamp, engage one wire at a time.





b.

for Type B:

i.
A345414C04
2.323,0.583 2.375,0.427 2.375,0.427 2.531,0.427 false 2.323,0.771 2.677,0.771 false 2.583,0.344 2.896,0.5 0.313,0.156 10 false *1 2.74,0.698 3.052,0.854 0.313,0.156 10 false *2
*1 O-ring
*2 Fuel Pump Spacer


Apply gasoline to a new O-ring. Then install the O-ring and fuel pump spacer to the fuel pump.


ii.

Install the fuel pump to the fuel tube supporter.


iii.

Engage the 3 claws to install the No. 2 fuel suction support to the fuel tube supporter.


iv.

Connect the fuel pump harness connector.


v.
A456287

Engage the claw to connect the fuel pump harness.

NOTICE:
·

Securely engage the claw.

·

Make sure that there is no foreign matter between the fuel pump and the ground terminal of the fuel pump harness.

·

Make sure that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.




vi.

Check the connection state of the fuel pump harness.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fuel pump body - Ground terminal of the fuel pump harness Always Below 50 Ω


If the result is not as specified, reconnect the fuel pump harness to the fuel pump so that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.


vii.

Engage the 4 claws to install the fuel suction plate sub-assembly to the fuel sub-tank sub-assembly.


viii.
A456298C01
2,1.146 2.125,1.146 2.125,1.146 2.323,1.438 true 2.875,1.854 2.708,1.854 2.708,1.854 2.5,1.521 true 1.813,1.073 1.979,1.229 0.167,0.156 10 true *a 2.927,1.781 3.094,1.938 0.167,0.156 10 true *b
*a Protrusion
*b Installation Hole
V100135

Slide


Align the protrusion of the fuel sub-tank sub-assembly with the installation hole of the fuel suction plate sub-assembly and then slide the fuel suction plate sub-assembly to install the fuel sub-tank sub-assembly.


ix.

Connect the 2 fuel pump harness connectors.


x.

Install the harness protector to the wire harness.


xi.

Engage the 2 clamps to connect the fuel pump harness to the fuel suction plate sub-assembly.

NOTICE:
·

Do not damage the wire harness.

·

When engaging each wire harness to the clamp, engage one wire at a time.