Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › ENGINE › 2017.09–2021.02
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324462 ENGINE G

A25A-FXS ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A379926

To prevent injury due to contact with an operating cooling fan, keep your hands and clothing away from the cooling fans when working in the engine compartment with the engine running or the power switch on (IG).


PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that the air cleaner filter element sub-assembly is not damaged or excessively oily.

HINT:
·

If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.


Hide 13750 6.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Rev up the engine several times. Check that the engine does not emit unusual noises.


c.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

HINT:

If any defects or problems are found during the inspection, perform the valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 7.INSPECT IGNITION TIMING

NOTICE:
·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in park.



a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Warm up and stop the engine.


c.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iii.

Enter the following menus: Powertrain / Engine / Data List / Ignition Timing Cylinder #1.

Powertrain > Engine > Data List
Tester Display
Ignition Timing Cylinder #1
50003 372 213
Standard Ignition Timing:

-2 to 14° BTDC at idle



iv.

Check that the ignition timing advances immediately when the engine speed is increased.


v.

Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / ON.

Powertrain > Engine > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Ignition Timing Cylinder #1
50004 372 22 213

vi.

Monitor Ignition Timing Cylinder #1 of the Data List.

Standard Ignition Timing:

8 to 12° BTDC at idle




d.

When not using the GTS:

i.

Remove the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


ii.
A206183C10
1.771,1.479 2.083,1.917 2.083,1.917 2.167,1.917 true 1.604,0.927 1.333,0.396 1.333,0.396 1.219,0.396 true 0.073,0.083 0.438,0.385 0.365,0.302 10 *a 2.208,1.833 2.521,2.031 0.313,0.198 10 TC 1,0.313 1.396,0.552 0.396,0.24 10 CG
*a DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Confirm the terminal numbers before connecting them. Connecting the wrong terminals may damage electrical components.



iii.
A407628

Connect the clip of a timing light to the ignition coil wire for the No. 1 cylinder.

NOTICE:

Use a timing light that detects primary signals.



iv.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


v.

Check the ignition timing at idle.

Standard Ignition Timing:

8 to 12° BTDC at idle



vi.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.


vii.

Check the ignition timing at idle.

Standard Ignition Timing:

-2 to 14° BTDC at idle



viii.

Confirm that the ignition timing advances immediately when the engine speed is increased.


ix.

Disconnect the clip of the timing light from the ignition coil wire for the No. 1 cylinder.


x.

Install the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION



Hide 8.INSPECT ENGINE IDLE SPEED

NOTICE:
·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in park.



a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Warm up and stop the engine.


c.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

e.

Read the value displayed on the GTS.

Standard Idle Speed:

1050 to 1150 rpm



Hide 9.INSPECT COMPRESSION

NOTICE:

Keep the spark plug holes free of foreign matter when measuring the compression pressure.


a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Warm up and stop the engine.



d.

Remove the front wheel opening extension pad RH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


e.

Remove the front wheel opening extension pad LH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


f.

g.

Remove the No. 2 engine under cover assembly (w/ Cover).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


h.

Remove the 4 spark plugs.

Click hereGeneral>MAINTENANCE>SPARK PLUG>REMOVAL

NOTICE:

DTCs will be stored if the inspection is performed with the ignition coil assembly connectors disconnected. Make sure that the ignition coil assembly connectors are connected during the inspection.



i.
A406639

Disconnect the fuel injector connector (for Port Injection).


j.
A403901C04
0.458,0.635 0.583,0.25 0.583,0.25 0.708,0.25 false 2.427,0.542 2.563,0.208 2.563,0.208 2.688,0.208 false 0.76,0.177 1.073,0.333 0.313,0.156 10 false *a 2.75,0.135 3.063,0.292 0.313,0.156 10 false *a
*a Lock Lever


Disengage the claw and raise the lock lever to disconnect the fuel injector connector (for Direct Injection) as shown in the illustration.


k.
A407627

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Connect the GTS to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Turn the GTS on.

NOTICE:

Check the HV battery voltage in the Data List to ensure that the battery is fully charged.



v.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Compression Test / ON.

Powertrain > Hybrid Control > Active Test
Tester Display
Compression Test
50004 397 42000

vi.

Depress and hold the brake pedal, and turn the power switch on (READY). Then check the compression pressure.

Standard Compression Pressure:

870 kPa (8.9 kgf/cm2, 126 psi)


Minimum Compression Pressure:

700 kPa (7.1 kgf/cm2, 102 psi)


Pressure Difference between Each Cylinder:

200 kPa (2.0 kgf/cm2, 29 psi) or less


NOTICE:
·

Noise may be emitted from the hybrid vehicle transaxle assembly. However, this is not a malfunction.

·

Inspect all cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




vii.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.





l.
A406642C02
1.917,0.458 2.063,0.458 2.063,0.458 2.208,0.667 false 1.74,0.365 2.052,0.563 0.313,0.198 10 false *a
*a Lock Lever


Connect the fuel injector connector (for Direct Injection) and push down the lock lever to engage the claw as shown in the illustration.


m.
A406639

Connect the fuel injector connector (for Port Injection).


n.

Install the 4 spark plugs.

Click hereGeneral>MAINTENANCE>SPARK PLUG>INSTALLATION


o.

Install the No. 2 engine under cover assembly (w/ Cover).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION



q.

Install the front wheel opening extension pad LH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


r.

Install the front wheel opening extension pad RH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


s.

Clear the DTCs.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

NOTICE:

After performing the inspection, clear the DTCs and confirm that DTCs are not stored again or that the normal system code is output if using a check wire.



Hide 10.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Run the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration at idle and then at an engine speed of 2500 rpm.

HINT:

When performing a 2 mode test (with the engine idling/running at 2500 rpm), the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect valve timing

-

Fouled, shorted or improperly gapped spark plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders

5.

Faulty EGR


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body with motor assembly


2.

Lean mixture causing misfire

3.

Faulty EGR


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI systems:

-

Fuel pressure regulator assembly

-

Engine coolant temperature sensor

-

Mass air flow meter sub-assembly

-

ECM

-

Fuel injector assemblies

-

Throttle position sensor (built into throttle body with motor assembly)


4.

Faulty EGR