Home › Engine / Hybrid System › A25A-FXS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM33C0E _51 Engine / Hybrid System _065420 A25A-FXS ENGINE MECHANICAL _0324466 REAR CRANKSHAFT OIL SEAL A

A25A-FXS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




c.
A400435C01
1.198,1.354 0.604,1.01 0.604,1.01 1.323,0.917 true 0.313,0.927 0.771,1.125 0.458,0.198 10 false SST 1.75,2.104 2.063,2.302 0.313,0.198 10 false *a
*a -0.9 to 1.1 mm


Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Standard Depth:

-0.9 to 1.1 mm (-0.0354 to 0.0433 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)


NOTICE:

Do not tap in the rear engine oil seal at an angle.



Hide 19315 2.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.

Type A:

i.
A400437

Install the No. 1 crankshaft position sensor plate.

HINT:

Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.




b.

Type B:

i.
A471041

Install the No. 1 crankshaft position sensor plate.

HINT:

Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.




Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A406361N02
1.406,0.854 2.125,0.521 2.125,0.521 1.781,0.802 true 2.208,0.438 2.667,0.635 0.458,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.

Clean the bolts and bolt holes.


c.

Apply adhesive to 2 or 3 threads at the end of each of the 8 new bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A406363N02
2.177,0.656 2.333,0.854 0.156,0.198 10 true 1 2.281,1.052 2.438,1.25 0.156,0.198 10 true 3 1.635,1.677 1.792,1.875 0.156,0.198 10 true 7 2.104,1.51 2.26,1.708 0.156,0.198 10 true 5 1.24,1.563 1.396,1.76 0.156,0.198 10 true 2 0.969,1.125 1.125,1.323 0.156,0.198 10 true 4 1.104,0.583 1.26,0.781 0.156,0.198 10 true 6 1.646,0.365 1.802,0.563 0.156,0.198 10 true 8

Install the flywheel sub-assembly with the 8 bolts. Uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:
150 N*m (1530 kgf*cm, 111 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.



Hide 31270 4.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

a.
A406361N03
1.406,0.854 2.125,0.521 2.125,0.521 1.781,0.802 true 2.208,0.438 2.667,0.635 0.458,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.
A406362N02
1.292,0.052 1.448,0.25 0.156,0.198 10 true 1 2.552,0.385 2.708,0.583 0.156,0.198 10 false 3 2.729,1.417 2.885,1.615 0.156,0.198 10 false 5 1.99,1.969 2.146,2.167 0.156,0.198 10 false 2 0.792,1.771 0.948,1.969 0.156,0.198 10 false 4 0.542,0.719 0.698,0.917 0.156,0.198 10 true 6

Install the transmission input damper assembly to the flywheel sub-assembly with the 6 bolts. Uniformly tighten the 6 bolts in the order shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Make sure that there are no oil on the transmission input damper assembly and flywheel sub-assembly.

·

Make sure to install the transmission input damper assembly in the correct direction.

·

Do not allow grease to contact the splines of the transmission input damper assembly and the input shaft.




Hide 30900 5.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY