Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › THROTTLE BODY
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0326944 THROTTLE BODY A

A25A-FXS ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 22271 1.INSTALL THROTTLE BODY GASKET

a.
A406014C01
1.01,0.375 1.229,0.375 1.229,0.375 1.406,0.719 true 0.76,0.302 1,0.479 0.24,0.177 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake manifold with the protrusion of the throttle body gasket oriented as shown in the illustration.


Hide 22030 2.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.
A406013C01
2.719,1.177 2.719,0.854 true 2.24,0.521 2.552,0.677 0.313,0.156 10 false *a 2.167,0.74 2.479,0.896 0.313,0.156 10 false *b 2.906,0.333 3.219,0.49 0.313,0.156 10 false *c 2.656,1.188 2.969,1.344 0.313,0.156 10 false *d 2.219,0.927 2.531,1.083 0.313,0.156 10 false *a
*a 45°(Claw of Clip Location)
*b Left of Vehicle
*c Top
*d Paint Mark


Connect the No. 6 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:
·

If the throttle body with motor assembly has been struck or dropped, replace it.

·

Make sure to position the clip as shown in the illustration.




b.
A406011C01
3.042,1.177 3.354,1.333 0.313,0.156 10 false *a 3.135,1.406 3.344,1.604 0.208,0.198 10 false *b 2.49,0.969 2.802,1.125 0.313,0.156 10 false *c 3.042,1.646 3.354,1.802 0.313,0.156 10 false *a
*a 45°(Claw of Clip Location)
*b Down
*c Right of Vehicle


Using an 8 mm socket wrench, install the throttle body with motor assembly to the intake manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 5 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



d.

Connect the throttle body with motor assembly connector.


Hide 3.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A417324C01
0.896,2.948 0.896,2.365 0.896,2.365 1.104,2.365 true 0.552,3.01 0.552,2.875 0.552,2.875 0.427,2.719 true 1.708,3.083 1.708,2.521 1.708,2.521 1.844,2.521 true 1.938,2.51 1.938,2.094 1.938,2.094 2.156,2.094 true 2.063,2.417 2.063,2.094 true 0.49,3.021 0.802,3.177 0.313,0.156 10 false *a 1.135,2.281 1.448,2.438 0.313,0.156 10 false *b 1.625,3.083 1.938,3.24 0.313,0.156 10 false *c 2.177,2 2.49,2.156 0.313,0.156 10 false *d 1.896,3.094 2.208,3.25 0.313,0.156 10 false *e 2.531,2.469 2.844,2.625 0.313,0.156 10 false *f 2.75,2.646 3.073,2.906 0.323,0.26 10 false *g
*a Protrusion
*b Cutout
*c Hose Clamp End
*d Paint Mark
*e 2 mm (0.0787 in.)
*f 4 mm (0.157 in.)
*g End of Hose Clamp Location


Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly.

NOTICE:

Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.



b.

Tighten the hose clamp in the position shown in the illustration.

NOTICE:

Make sure that the end of the hose clamp is positioned as shown in the illustration.



c.

Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.


d.

Engage the 2 air cleaner cap clamps.


e.
A406009C01
1,1.458 1.094,1.271 1.094,1.271 1.208,1.271 true 0.896,1.063 1.208,1.219 0.313,0.156 10 false *a 0.26,1.563 0.573,1.719 0.313,0.156 10 false *b 0.323,1.344 0.635,1.5 0.313,0.156 10 false *c 1.24,1.198 1.552,1.354 0.313,0.156 10 false *d 0.323,1.75 0.635,1.906 0.313,0.156 10 false *c
*a Top
*b Front of Vehicle
*c 45°(Claw of Clip Location)
*d Paint Mark


Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



f.

Engage the wire harness clamp.


g.

Connect the mass air flow meter sub-assembly connector.


Hide 17750A 4.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 5.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 12601B 6.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 7.ADD ENGINE COOLANT (for Engine)

Hide 8.INSPECT FOR COOLANT LEAK (for Engine)

Hide 9.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.

·

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.



a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372


f.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

g.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

Standard Idle Speed:

1050 to 1150 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P.




h.

Perform a road test and confirm that there are no abnormalities.