Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › INVERTER WITH CONVERTER
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0328987 INVERTER WITH CONVERTER A

HYBRID / BATTERY CONTROL  INVERTER WITH CONVERTER  INSTALLATION  


PROCEDURE

Hide G921E 1.INSTALL INVERTER PROTECTOR

a.
A406200C02
1.198,1.5 0.948,1.5 0.948,1.5 0.677,0.917 true 1.24,1.427 1.552,1.583 0.313,0.156 10 false *a
*a Pin


Install the inverter protector to the inverter with converter assembly with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)

NOTICE:

Make sure to align the hole of the inverter protector with the pin.



Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the inverter with converter assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the wire harness clamp bracket to the inverter with converter assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install the 2 wire harness clamp brackets to the inverter with converter assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide G9215 3.INSTALL NO. 2 INVERTER BRACKET

NOTICE:
A406195C03
0.875,1.094 1.75,1.958 1.75,1.958 2.396,1.135 true 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.698,1.99 2.01,2.146 0.313,0.156 10 false *b
*a Bottom of Inverter with Converter Assembly
*b Support


Make sure to support the inverter with converter assembly at the positions shown in the illustration, otherwise it may be damaged.


a.
A406196C04
2.25,1.979 2.927,2 2.927,2 2.698,1.75 false 2.969,1.938 3.281,2.094 0.313,0.156 10 false *a 0.688,1.031 0.844,1.229 0.156,0.198 10 false 1 1.375,1.531 1.531,1.729 0.156,0.198 10 true 2
*a Wooden Block


Set the inverter with converter assembly on wooden blocks.


b.

Temporarily install the No. 2 inverter bracket to the inverter with converter assembly with the 2 bolts.


c.

Fully tighten the 2 bolts in the order shown in the illustration.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide G9214 4.INSTALL NO. 1 INVERTER BRACKET

a.
A406194C04
2.208,1.948 2.906,1.958 2.906,1.958 2.615,1.719 false 2.958,1.885 3.271,2.042 0.313,0.156 10 false *a 0.625,1.021 0.781,1.219 0.156,0.198 10 false 1 1.438,1.5 1.594,1.698 0.156,0.198 10 true 2
*a Wooden Block


Temporarily install the No. 1 inverter bracket to the inverter with converter assembly with the 2 bolts.


b.

Fully tighten the 2 bolts in the order shown in the illustration.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide G9200 5.INSTALL INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.

Temporarily install the inverter with converter assembly with the 5 bolts and 2 nuts.

NOTICE:
·

When installing the inverter with converter assembly, be careful not to damage the parts around it.

·

To prevent damage, do not hold the inverter with converter assembly by the connectors, brackets or cooling pipes.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·
A406201C02
0.604,2.219 0.813,2.406 0.208,0.188 10 true *a 0.604,3.344 0.823,3.521 0.219,0.177 10 true *b
*a Correct
*b Incorrect


Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.



HINT:

If the bolts and nuts are not tightened appropriately, the inverter with converter assembly may make an abnormal noise.



b.

Fully tighten the bolt (A).

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)

A406202N02
1.302,1.479 1.458,1.677 0.156,0.198 10 true A 2.167,1.542 2.323,1.719 0.156,0.177 10 true B 1.823,1.563 1.979,1.74 0.156,0.177 10 true B 2.458,1.333 2.615,1.51 0.156,0.177 10 true B 5.698,2.385 5.854,2.563 0.156,0.177 10 true C 4.5,2.375 4.656,2.552 0.156,0.177 10 true D 4.948,2.563 5.104,2.74 0.156,0.177 10 true D


c.

Fully tighten the 3 bolts (B).

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


d.

Fully tighten the bolt (C).

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


e.

Fully tighten the 2 nuts (D).

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide G1148 6.CONNECT MOTOR CABLE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.

Temporarily connect the motor cable to the inverter with converter assembly with the 4 bolts.

NOTICE:
·

Do not touch the waterproof seal or terminals of the motor cable.

·

Do not damage the terminals, connector housing or inverter with converter assembly during connection.




b.
A406191C04
0.99,0.25 1.323,0.25 1.323,0.25 1.573,0.469 true 0.813,0.177 1.125,0.333 0.313,0.156 10 false *a 2.99,1.802 3.146,2 0.156,0.198 10 true A 0.823,2.594 0.979,2.792 0.156,0.198 10 true 1 0.552,1.885 0.677,2.063 0.125,0.177 10 true 2 2.76,2.438 2.896,2.604 0.135,0.167 10 true 3
*a Waterproof Seal


Fully tighten the bolt (A).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Fully tighten the 3 bolts in the order shown in the illustration to connect the motor cable to the inverter with converter assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.
A406190

Temporarily install the 6 bolts.

NOTICE:
·

To prevent the threads from being damaged, temporarily tighten the 6 bolts by hand.

·

Do not touch the waterproof seal or terminals of the motor cable.

·

Do not damage the terminals, connector housing or inverter with converter assembly during connection.




e.

Using an insulated tool, fully tighten the 6 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Do not touch the waterproof seal or terminals of the motor cable.

·

Do not damage the terminals, connector housing or inverter with converter assembly during connection.

·

Be sure to use a torque wrench to tighten the bolts.




Hide G9221 7.INSTALL INVERTER COVER

CAUTION:

Be sure to wear insulated gloves.


a.

Install the inverter cover to the inverter with converter assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Visually confirm that the inverter cover waterproof seal is securely installed before installing the inverter cover.

·

Do not touch the waterproof seal of the inverter cover.

·

Make sure that the interlock is fully engaged.

·

Do not damage the terminals, interlock connector or inverter with converter assembly during installation.

·

Do not allow any foreign matter or water to enter the inverter with converter assembly.

·
A376320C03
2.167,2.115 2.656,1.635 2.656,1.635 2.031,1.24 false 1.031,0.313 1.302,0.313 1.302,0.313 1.823,0.781 true 0.865,0.188 1.177,0.385 0.313,0.198 10 false *a 2.698,1.521 3.01,1.719 0.313,0.198 10 false *1
*1 Inverter Cover
*a Screw


Do not remove or excessively tighten the screw of the inverter cover.

·

Although the inverter cover may feel loose, this is not due to a malfunction.

·
A406203C02
1.667,1.885 1.875,2.063 0.208,0.177 10 true *a
*a No Gap


Push in the inverter cover until it contacts the inverter with converter assembly.




Hide G9228A 8.CONNECT NO. 4 INVERTER COOLING HOSE

a.
A406204C02
0.76,0.958 0.667,0.594 0.667,0.594 0.469,0.594 true 1.292,0.979 1.156,0.458 1.156,0.458 0.958,0.458 true 0.302,0.5 0.615,0.656 0.313,0.156 10 false *a 0.802,0.375 1.115,0.531 0.313,0.156 10 false *b 1.083,1.552 1.396,1.708 0.313,0.156 10 false *c 2.323,0.135 2.635,0.292 0.313,0.156 10 false *d 3.01,0.917 3.323,1.073 0.313,0.156 10 false *e 2.635,0.375 3.01,0.563 0.375,0.188 10 false 120°
*a Alignment Mark (Yellow)
*b Rib
*c 2 to 7 mm (0.0787 to 0.276 in.)
*d Up
*e LH Side


Connect the No. 4 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:
·

To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.

·

Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.



HINT:

Make sure that the clip is positioned as shown in the illustration.



Hide G9225K 9.CONNECT NO. 1 INVERTER COOLING HOSE

a.
A406205C02
0.49,0.521 0.667,0.521 0.667,0.521 0.76,0.958 true 1,0.375 1.177,0.375 1.177,0.375 1.292,0.958 true 0.323,0.427 0.635,0.583 0.313,0.156 10 false *a 0.833,0.292 1.146,0.448 0.313,0.156 10 false *b 1.073,1.552 1.385,1.708 0.313,0.156 10 false *c 2.323,0.135 2.635,0.292 0.313,0.156 10 false *d 3.01,0.927 3.323,1.083 0.313,0.156 10 false *e 2.635,0.354 3.073,0.563 0.438,0.208 10 false 120°
*a Alignment Mark (Yellow)
*b Rib
*c 2 to 7 mm (0.0787 to 0.276 in.)
*d Up
*e LH Side


Connect the No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:
·

To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.

·

Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.



HINT:

Make sure that the clip is positioned as shown in the illustration.



Hide 33820B 10.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the inverter with converter assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
C377951N01
2.833,1.385 2.99,1.583 0.156,0.198 10 false N 2.583,2 2.75,2.177 0.167,0.177 10 false P

Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.


c.

Engage the 2 claws to install a new clip to the transmission control cable assembly.


d.
C377953C01
1.25,1.385 0.969,0.573 0.969,0.573 2.167,1.365 true 1.146,1.635 2.948,2.521 2.948,2.521 2.313,1.646 true 2.646,1.063 2.75,0.698 2.75,0.698 2.896,0.698 false 1.26,2.979 1.406,2.979 1.406,2.979 1.583,2.417 true 1.094,2.917 1.385,3.156 0.292,0.24 10 false *1 2.958,0.625 3.26,0.802 0.302,0.177 10 false *2 0.792,0.479 1.104,0.667 0.313,0.188 10 false *a 3,2.469 3.313,2.625 0.313,0.156 10 false *b
*1 Transmission Control Cable Assembly
*2 No. 1 Transmission Control Cable Bracket
*a Claw (A)
*b Claw (B)


Using a screwdriver, engage the 4 claws and install the transmission control cable assembly to the No. 1 transmission control cable bracket.

NOTICE:
·

Make sure that the claws (A) of the clip are securely engaged in the grooves of the bracket.

·

Make sure that the transmission control cable assembly is securely installed inside of the claws (B) of the clip.




e.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 82121 11.CONNECT ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A406185

Engage the 2 clamps and connect the engine wire to the inverter with converter assembly.


b.

Temporarily install the nut.

NOTICE:

To prevent the threads from being damaged, temporarily tighten the nut by hand.



c.

Fully tighten the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Engage the 2 claws to close the engine wire terminal cover.


e.
A406183

Connect the engine wire to the inverter with converter assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.
A406182

Connect the engine wire to the inverter with converter assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


g.

Engage the 2 clamps.


h.

Engage the clamp.


i.

Confirm that no foreign matter or water has entered the connector of the generator temperature sensor, resolver (transmission fluid temperature sensor) and shift lever position sensor and connect the 3 connectors.


j.
A406179N04
2.292,0.521 2.417,0.677 0.125,0.156 10 true B 2.479,2.198 2.604,2.354 0.125,0.156 10 true A 1.042,2.365 1.167,2.521 0.125,0.156 10 true A

Engage the clamp (B).


k.

Connect the engine wire to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


l.

Engage the 2 clamps (A) and connect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.


m.
A406178N04
1.979,0.271 2.125,0.427 0.146,0.156 10 true A 1.979,0.74 2.125,0.896 0.146,0.156 10 true A 1.01,1.656 1.156,1.813 0.146,0.156 10 true A 1.125,0.406 1.271,0.563 0.146,0.156 10 true B 1.208,3.063 1.354,3.219 0.146,0.156 10 true B

Engage the 2 clamps (B).


n.

Connect the engine wire to the inverter with converter assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


o.

Engage the 3 clamps (A) and connect the No. 1 fuel vapor feed hose.


p.
A406206

Connect the inverter with converter assembly connector and move the lock lever to lock them.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connectors.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.




Hide 12.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the inverter with converter assembly with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 821H2 13.CONNECT HV AIR CONDITIONING WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406173C02
1.219,0.542 1.438,0.333 1.438,0.333 1.948,0.333 true 1.99,0.25 2.302,0.406 0.313,0.156 10 false *a
*a Waterproof Seal


Engage the clamp and connect the HV air conditioning wire to the inverter with converter assembly.

NOTICE:
·

Do not allow any foreign matter or water to enter the inverter with converter assembly.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.




b.

Install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 821H1 14.CONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A406208C02
0.74,0.646 1.01,0.188 1.01,0.188 1.417,0.188 true 1.458,0.125 1.771,0.281 0.313,0.156 10 false *a
*a Waterproof Seal


Engage the 2 clamps and connect the HV floor under wire to the inverter with converter assembly.

NOTICE:
·

Do not allow any foreign matter or water to enter the inverter with converter assembly.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.




b.

Install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 82111 15.CONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the clamp to connect the engine room main wire to the inverter with converter assembly.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A406212

Connect the inverter with converter assembly connector and move the lock lever to lock them.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connectors.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.




Hide 17.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A406008C01
0.417,2.719 0.563,2.927 0.563,2.927 0.563,3.063 true 1.104,2.365 0.906,2.365 0.906,2.365 0.906,2.917 true 1.865,2.479 1.865,2.104 1.865,2.104 2.052,2.104 true 1.99,2.469 2.5,2.469 true 1.844,2.625 1.844,3.052 true 0.5,3.063 0.813,3.219 0.313,0.156 10 false *a 1.135,2.302 1.448,2.458 0.313,0.156 10 false *b 2.083,2.031 2.396,2.188 0.313,0.156 10 false *c 2.531,2.396 2.844,2.552 0.313,0.156 10 false *d 2.323,3.198 2.635,3.354 0.313,0.156 10 false *e 2.656,2.844 2.969,3 0.313,0.156 10 false *f 1.792,3.063 2.104,3.219 0.313,0.156 10 false *d
*a Protrusion
*b Cutout
*c Hose Clamp Tip
*d Alignment Mark (Blue)
*e 2 mm (0.0787 in.)
*f 4 mm (0.157 in.)


Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly.

NOTICE:

Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.



b.

Tighten the hose clamp in the position shown in the illustration.

NOTICE:

Make sure that the end of the hose clamp is positioned between the paint marks as shown in the illustration.



c.
A406009C02
1,1.458 1.094,1.271 1.094,1.271 1.208,1.271 true 0.896,1.094 1.208,1.25 0.313,0.156 10 false *a 0.26,1.563 0.573,1.719 0.313,0.156 10 false *b 1.24,1.198 1.552,1.354 0.313,0.156 10 false *c 0.302,1.333 0.76,1.531 0.458,0.198 10 false 45° 0.292,1.781 0.75,1.979 0.458,0.198 10 false 45°
*a Top
*b Front of Vehicle
*c Alignment Mark (Yellow)


Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

HINT:

Make sure that the clip is positioned as shown in the illustration.



d.

Engage the 2 grommets and pin to install the air cleaner assembly with air cleaner hose.


e.

Engage the wire harness clamp.


f.

Connect the mass air flow meter sub-assembly connector.


Hide 17750A 18.INSTALL INLET AIR CLEANER ASSEMBLY

a.
A406772C02
0.521,1.74 0.677,1.958 0.156,0.219 10 true 1 1.323,1.74 1.479,1.958 0.156,0.219 10 true 2

Temporarily install the inlet air cleaner assembly with the 2 bolts.


b.

Fully tighten the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 53295E 19.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 12601B 20.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 22.ADD COOLANT (for Inverter)

Hide 24.PERFORM INITIALIZATION