Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 1) › 2017.09–2019.10
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0326953 AIR FUEL RATIO SENSOR(for Sensor 1) A

A25A-FXS ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 1)  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.
A414851C01
1.177,1.74 1.74,1.74 true 1.948,2.979 2.51,2.979 true 0.021,0.031 0.323,0.271 0.302,0.24 12 true *A 0.021,2.365 0.323,2.615 0.302,0.25 12 true *B 1.708,0.198 1.927,0.427 0.219,0.229 10 true *a 0.948,3.313 1.167,3.542 0.219,0.229 10 true *a 1.76,1.656 2.146,1.865 0.385,0.208 10 true SST 2.531,2.896 2.917,3.104 0.385,0.208 10 true SST
*A for LHD
*B for RHD
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold (TWC: Front Catalyst).

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.
A406055C01
2.729,0.51 2.729,0.219 2.729,0.219 2.896,0.219 true 2.708,0.865 2.323,1 2.323,1 2.5,0.49 true 2.938,0.146 3.167,0.365 0.229,0.219 10 true *a 2.24,1.021 2.458,1.198 0.219,0.177 10 true *b
*a Tie Band
*b Wire Harness Clamp


Connect the air fuel ratio sensor connector.


c.

Engage the 3 wire harness clamps so that the tie band is positioned as shown in the illustration.


Hide 12601B 2.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 4.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION