Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › 2017.09–2019.02
RM33C0E _59 Vehicle Exterior _065474 EXTERIOR PANELS / TRIM _0328281 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REASSEMBLY  


PROCEDURE

Hide 52536 1.INSTALL FRONT BUMPER SIDE RETAINER LH

a.
B470417C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips as shown in the illustration.


b.
B470415

Install the front bumper side retainer LH with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 52535 2.INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 52131A 3.INSTALL FRONT BUMPER REINFORCEMENT

a.

Install the front bumper reinforcement with the 6 bolts.

B481987

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.
B489578

Engage the 5 clamps.



d.

Install the headlight assembly RH.

HINT:

Use the same procedure as for the LH side.



Hide 52611 4.INSTALL FRONT BUMPER ENERGY ABSORBER

a.
B489579C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 guides to install the front bumper energy absorber as shown in the illustration.


Hide 53879H 5.INSTALL FRONT FENDER LINER RETAINER

a.
B479551C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the 2 front fender liner retainers as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 47749F 6.INSTALL PIN HOLD CLIP

a.
B610732C02
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the 2 pin hold clips as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 53124B 7.INSTALL RADIATOR GRILLE SIDE MOULDING LH (for Mesh Type Radiator Grille)

a.
B470410

Engage the 2 guides and 2 claws.


b.
B470409

Install the radiator grille side moulding LH with the 2 clips.


Hide 53123B 8.INSTALL RADIATOR GRILLE SIDE MOULDING RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 53102A 9.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)

a.

Engage the 23 claws.

B470375


b.
B470374

Install the lower radiator grille sub-assembly with the 6 screws.


Hide 53102A 10.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)

a.

Engage the 18 claws.

B470408


b.
B470407

Install the lower radiator grille sub-assembly with the 2 screws.


Hide 81482C 11.INSTALL FOG LIGHT COVER LH (for Mesh Type Radiator Grille)

a.
B473128

Engage the 6 claws to install the fog light cover LH.


Hide 81481E 12.INSTALL FOG LIGHT COVER RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 53124D 13.INSTALL LOWER RADIATOR GRILLE MOULDING LH (for Mesh Type Radiator Grille)

a.
B470406

Engage the 10 claws to install the lower radiator grille moulding LH.


Hide 53123C 14.INSTALL LOWER RADIATOR GRILLE MOULDING RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 53123D 15.INSTALL LOWER RADIATOR GRILLE MOULDING (for Mesh Type Radiator Grille)

a.

Engage the 16 claws.

B470405


b.
B470404

Install the lower radiator grille moulding with the 2 screws.


Hide 81220 16.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 17.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 53111 18.INSTALL RADIATOR GRILLE (for Bar Type Radiator Grille)

a.
B488714

Install the 6 screws.


b.
B470372

Install the radiator grille with the 2 clips.


Hide 53111 19.INSTALL RADIATOR GRILLE (for Mesh Type Radiator Grille)

a.
B470403

Install the 10 screws.


b.
B470402

Install the radiator grille with the 2 clips.


Hide 53124B 20.INSTALL RADIATOR GRILLE SIDE MOULDING LH (for Bar Type Radiator Grille)

a.
B470371C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 claws as shown in the illustration.


b.
B470369

Install the radiator grille side moulding LH with the screw.


Hide 53123B 21.INSTALL RADIATOR GRILLE SIDE MOULDING RH (for Bar Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 75310A 22.INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY

a.
B470368

Engage the guide and 2 claws.


b.
B470367

Install the radiator grille emblem assembly with the 2 screws.


Hide 53395E 23.INSTALL HOOD TO FRONT END PANEL SEAL

HINT:

When installing the hood to front end panel seal, heat the front bumper cover using a heat light.


Heating Temperature
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B470366C01
0,0 0,0 false
V100155

Double-sided Tape


Engage the guide to attach the double-sided tape as shown in the illustration.

HINT:

Press the hood to front end panel seal firmly to install it.



c.
B470365

Engage the 6 clips to install a new hood to front end panel seal.


d.

Remove the release paper from the hood to front end panel seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



Hide 52128B 24.INSTALL FRONT BUMPER HOLE COVER LH (for Bar Type Radiator Grille)

a.
B499297C01
1,0.708 1,0.396 false 0.938,0.698 1.208,0.917 0.271,0.219 10 false *a
*a Hook
V113147

Install in this Direction


Engage the hook.


b.

Engage the 4 claws to install the front bumper hole cover LH as shown in the illustration.


Hide 52128B 25.INSTALL FRONT BUMPER HOLE COVER LH (for Mesh Type Radiator Grille)

a.
B499299C02
2.667,0.573 2.917,0.427 false 2.927,0.313 3.302,0.604 0.375,0.292 10 false *a
*a Hook
V113147

Install in this Direction


Engage the hook.


b.

Engage the 6 claws to install the front bumper hole cover LH as shown in the illustration.


Hide 52127D 26.INSTALL FRONT BUMPER HOLE COVER RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 27.INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

a.

Engage the 7 clamps to install the headlight cleaner hose.

B483727


Hide 85208A 28.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85207A 29.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure as for the LH side.


Hide 85354 30.INSTALL HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)

Hide 85353 31.INSTALL HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure as for the LH side.


Hide 82114 32.INSTALL NO. 4 ENGINE ROOM WIRE

a.

for Bar Type Radiator Grille:

i.

Engage the 10 clamps to install the No. 4 engine room wire.

B489430



b.

for Mesh Type Radiator Grille:

i.

Engage the 12 clamps to install the No. 4 engine room wire.

B489431



Hide 89347B 33.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

Hide 52423A 35.INSTALL FRONT BUMPER PAD LH (for Bar Type Radiator Grille)

a.
B470364

Engage the guide and 2 claws to install the front bumper pad LH.


Hide 52422A 36.INSTALL FRONT BUMPER PAD RH (for Bar Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52423A 37.INSTALL FRONT BUMPER PAD LH (for Mesh Type Radiator Grille)

a.
B488713

Engage the guide and 2 claws to install the front bumper pad LH.


Hide 52422A 38.INSTALL FRONT BUMPER PAD RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52114A 39.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Bar Type Radiator Grille)

a.
B499303C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws as shown in the illustration.


b.
B489558

Install the front bumper extension mounting bracket with the 2 screws.


Hide 52114A 40.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Mesh Type Radiator Grille)

a.
B499301C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 guides and 2 claws as shown in the illustration.


b.
B483731

Install the front bumper extension mounting bracket with the 2 screws.


Hide 88211B 41.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)