Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front) › 2017.09–2019.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0334379 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 89305 1.INSTALL ULTRASONIC SENSOR CUSHION SET

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Install the ultrasonic sensor cushion set as shown in the illustration.

E488345C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 89347B 2.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

If a front corner ultrasonic sensor retainer has been removed, replace it with a new one. Install the front corner ultrasonic sensor with a new front corner ultrasonic sensor retainer as a set to the front bumper assembly.



a.
E366461

Engage the 2 claws to install a new front corner ultrasonic sensor retainer to the front corner ultrasonic sensor.


b.

Clean the surface of the front bumper assembly.

i.

Remove any remaining double-sided tape from the front bumper assembly.


ii.

Wipe off any adhesive residue with cleaner.



c.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 19 mm (0.748 in.)


Cover the sensor installation hole with a 19 mm (0.748 in.) circular piece of tape.


d.

for Bar Type Radiator Grille:

i.
E375836C01
0,0 0,0 false
V100145

Primer


Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the front bumper assembly until the primer has dried.





e.

Mesh Type Radiator Grille:

i.
E375837C01
0,0 0,0 false
V100145

Primer


Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the front bumper assembly until the primer has dried.





f.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


g.

Peel off the release paper from the front corner ultrasonic sensor retainer.


h.

for Bar Type Radiator Grille:

i.
E375838C01
1.875,1.813 1.875,1.563 false 1.781,1.833 2,2.01 0.219,0.177 10 true *a
*a Scribed Line
V100155

Press area


Align the front corner ultrasonic sensor retainer with front corner ultrasonic sensor with the mark on the front bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the sensor tip is correctly inserted into the sensor installation hole of the front bumper assembly.

·

Ensure that the front corner ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front corner ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper assembly. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper assembly.




i.

Mesh Type Radiator Grille:

i.
E375839C01
2.135,1.75 2.042,1.469 false 2.073,1.75 2.271,1.948 0.198,0.198 10 true *a
*a Scribed Line
V100155

Press area


Align the front corner ultrasonic sensor retainer with front corner ultrasonic sensor with the mark on the front bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the sensor tip is correctly inserted into the sensor installation hole of the front bumper assembly.

·

Ensure that the front corner ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front corner ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper assembly. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper assembly.




Hide 89348J 3.INSTALL ULTRASONIC SENSOR CLIP (for Bar Type Radiator Grille)

HINT:

Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.


a.
E375835

Engage the clamp to install the ultrasonic sensor clip to the wire.


Hide 89341K 4.INSTALL FRONT CORNER ULTRASONIC SENSOR

a.

for Bar Type Radiator Grille:

i.
E375829C01
0,0 0,0 false
V113147

Install in this Direction


When replacing only the front corner ultrasonic sensor:

1.

Engage the 2 claws to install the front corner ultrasonic sensor as shown in the illustration.



ii.
E375827C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.


iii.

Connect the connector.



b.

for Mesh Type Radiator Grille:

i.
E375832C01
0,0 0,0 false
V113147

Install in this Direction


When replacing only the front corner ultrasonic sensor:

1.

Engage the 2 claws to install the front corner ultrasonic sensor as shown in the illustration.



ii.

Connect the connector.



Hide 5.INSTALL FRONT BUMPER ASSEMBLY