Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1345  Linear Solenoid Valve Offset Learning undone  C1368  Linear Solenoid Valve Offset  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores the individual characteristics of each linear solenoid built into the brake booster with master cylinder assembly. Based on the stored information, the skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.

The skid control ECU (brake booster with master cylinder assembly) receives the shift position P signal from the hybrid vehicle control ECU assembly through the CAN communication system.

These DTCs are cleared when the linear solenoid valve offset learning results are normal.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1345 Linear Solenoid Valve Offset Learning undone 1133 The linear solenoid valve offset learning value is not stored. Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal. Electronically controlled brake system DTC
HINT:

During Test Mode, related DTCs are cleared.


C1368 Linear Solenoid Valve Offset 1134 The linear solenoid valve offset learning value cannot be obtained.
·

Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


HINT:

Before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C1203 will be output.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check that DTCs other than C1345, C1349 and C1392 are not output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

DTCs other than C1345, C1349 and C1392 are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM AIR BLEEDING

NG

2.PERFORM AIR BLEEDING
a.

Perform the air bleeding procedure in Bleed Brake System.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


Result:
Proceed to
NEXT



NEXT

3.PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
3.PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
a.

Turn the power switch off.


b.

Check and ensure the following conditions required for performing linear solenoid valve offset learning and then perform linear solenoid valve offset learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167
1.

The auxiliary battery voltage is 11 to 15.5 V when the power switch is on (READY).

2.

The brake actuator (brake booster with master cylinder assembly) is not hot.

3.

The hybrid control system is not malfunctioning.

4.

The shift state indicator shows that the shift lever is in P.

5.

The READY light in the combination meter assembly is illuminated.

6.

The brake pedal is not depressed.

7.

The parking brake is released.

8.

DTC C1451 (Motor Drive Permission Malfunction) is not output. (If it is output, bleed the air from the high-pressure tube.)



Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1345 and C1368 are not output. A
DTCs C1345 and/or C1368 are output. B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY