The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.PERFORM ACCUMULATOR PRESSURE ZERO DOWN
Using the GTS, perform the accumulator pressure zero down operation.
Connect the GTS to the DLC3 with the power switch off.
Turn the power switch on (IG).
Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.
| Tester Display |
|---|
| ECB Utility |
Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.
Perform "Motor Invalid" according to the display on the GTS.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.
| Tester Display |
|---|
| ECB Utility |
Select "ECB (Electronically Controlled Brake system) Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.
Perform "ECB (Electronically Controlled Brake system) Invalid" according to the display on the GTS.
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.
Check that the brake pedal is firm.
If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.
Turn the GTS off and turn the power switch off.
Disconnect the GTS from the DLC3.
Disconnect the cable from the negative (-) auxiliary battery terminal.
When the accumulator pressure zero down could not be performed using the GTS.
If DTCs are output, the accumulator pressure zero down operation may not be complete. In this case, perform the following procedure.
|
Release the lock lever |
|
Disconnect the connector |
With the power switch off, release the lock lever and disconnect the brake booster pump assembly connector as shown in the illustration.
Be careful not to allow any brake fluid to enter the connector.
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal is firm.
If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.
Disconnect the cable from the negative (-) auxiliary battery terminal.
55708
3.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53607A
4.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
Disconnect the connector.
Disengage the 2 clamps and separate the wire harness.
Remove the 6 bolts, 4 nuts and front center upper suspension brace sub-assembly.
5.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
82111
6.DISCONNECT ENGINE ROOM MAIN WIRE
Disconnect the connector from the brake booster with master cylinder assembly.
| *a | Lock Lever |
| *b | Lock Arm |
| *c | Push |
|
Release the lock lever |
Push the lock arm of the connector to disengage the lock and release the lock lever as shown in the illustration.
| *a | Screwdriver Insertion Point |
| *b | Pre-lock |
|
Disconnect the connector |
Using a screwdriver, release the pre-lock and disconnect the connector from the brake booster with master cylinder assembly as shown in the illustration.
Be careful not to allow any brake fluid to enter the connector.
44571A
7.DISCONNECT NO. 1 BRAKE ACTUATOR HOSE
Slide the clip and disconnect the No. 1 brake actuator hose from the brake booster with master cylinder assembly.
8.DISCONNECT BRAKE LINE
Using a union nut wrench, disconnect the 3 brake lines from the brake booster with master cylinder assembly.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
55606
9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
47264A
10.REMOVE PUSH ROD PIN
Remove the clip and push rod pin.
47210L
11.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
| *a | Skid Control ECU |
| *b | No. 1 Reservoir Hose |
| *c | Brake Master Cylinder Push Rod Clevis |
| *d | Boot |
| *e | Master Cylinder Reservoir Assembly |
Remove the 4 nuts and brake booster with master cylinder assembly.
Do not kink or damage the brake lines.
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.
Be careful not to allow any brake fluid to enter the connector.
44785D
12.REMOVE BRAKE MASTER CYLINDER GASKET