Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1311  Open Circuit in Main Relay 1  C1312  Short Circuit in Main Relay 1  


DESCRIPTION

The main relay supplies power to the switching solenoid and the linear solenoid.

The main relay remains on for approximately 2 minutes after the power switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1311 Open Circuit in Main Relay 1 1 Either of the following is detected:
1.

When the power switch is on (READY):

The BS terminal voltage is less than 3.5 V for 0.05 seconds or more, when the IG1 terminal voltage is 9.5 V or more and operation of the main relay is requested.

2.

When the power switch is off:

The BS terminal voltage is less than 3.5 V for 0.05 seconds or more, when operation of the main relay is requested.


·

Open or short in main relay circuit

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1312 Short Circuit in Main Relay 1 2 The BS terminal voltage is 3.5 V or more for 4.5 seconds or more, when operation of the main relay is requested.
·

Short in main relay circuit

·

Main relay internal stuck

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC

DTC Detection Conditions: C1311 INF Code: 1
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the power switch is on (READY), the IG1 terminal voltage is 9.5 V or more. ○ -
When the power switch is off. - ○
Malfunction Status The BS terminal voltage is less than 3.5 V, when operation of the main relay is requested. ○ -
The BS terminal voltage is less than 3.5 V, when operation of the main relay is requested. - ○
Detection Time 0.05 seconds or more 0.05 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake booster with master cylinder assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MAIN RELAY)
a.

Select the Active Test on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Main Relay Main relay Relay ON/OFF ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Main Relay Main relay operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
ECB Main Relay
Data List Display
ECB Main Relay
50004 105 37 65

b.

Check that the condition of the main relay observed on the GTS changes according to GTS operation.


Result:
Result Proceed to
Main relay in the Data List turns ON/OFF using the Active Test. A
Main relay in the Data List does not change using the Active Test. B



A

2.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

B

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
2.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.
C378330C08
0.302,0.698 0.708,0.979 0.406,0.281 2.677,2.896 2.51,2.26 true 0.385,0.771 0.844,0.969 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 2.635,2.906 2.948,3.104 0.313,0.198 10 false BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-52 (BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch off.


d.

Turn the power switch on (IG).


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1311 and C1312 are not output. A
DTCs C1311 and/or C1312 are output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
a.
C378330C09
0.438,0.698 0.844,0.979 0.406,0.281 1.438,1.885 1.25,1 true 1.615,1.615 1.906,0.99 true 1.073,0.802 1.531,1 0.458,0.198 10 false +BI1 0.531,0.771 0.99,0.969 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.792,0.802 2.406,1 0.615,0.198 10 false +BI2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-15 (+BI1) - Body ground Always 11 to 14 V
A40-5 (+BI2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BI CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.
C378330C08
0.302,0.698 0.708,0.979 0.406,0.281 2.677,2.896 2.51,2.26 true 0.385,0.771 0.844,0.969 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 2.635,2.906 2.948,3.104 0.313,0.198 10 false BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-52 (BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)