Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2017.09–2020.08
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1259  HV Control System Regenerative Malfunction  C1310  HV System Malfunction  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) communicates with the hybrid vehicle control ECU assembly and controls braking force according to the motor's regenerative force.

The skid control ECU (brake booster with master cylinder assembly) sends VSC+/VSC and cooperative control with EPS signals to the hybrid vehicle control ECU assembly and receives operating signals from the hybrid vehicle control ECU assembly.

The skid control ECU (brake booster with master cylinder assembly) uses CAN communication for communicating with the hybrid vehicle control ECU assembly. If a communication malfunction is detected, the skid control ECU (brake booster with master cylinder assembly) prohibits VSC+/VSC and cooperative control with EPS operation, brake hold operation and part of the electronically controlled brake system control as a fail-safe function.

If the signals from the hybrid vehicle control ECU assembly return to normal, the warning light will go off and the DTCs C1259 and C1310 will be cleared.

HINT:

These DTCs will be output from the skid control ECU (brake booster with master cylinder assembly) when the hybrid vehicle control ECU assembly sends a malfunction signal to the skid control ECU (brake booster with master cylinder assembly).


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1259 HV Control System Regenerative Malfunction 1132 A regeneration malfunction signal is input for at least 0.036 seconds when IG2 terminal voltage is 9.5 V or more for at least 2 seconds and communication with the hybrid vehicle control ECU assembly is valid.
·

Hybrid vehicle control ECU assembly

(Regeneration malfunction)

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
HINT:

The DTC is cleared when the conditions return to normal.


C1310 HV System Malfunction 1140
1141
·

INF Code: 1140

-

When the IG2 terminal voltage is 9.5 V or more for 2 seconds or more and communication with the hybrid vehicle control ECU assembly is possible, an internal malfunction signal is detected for 0.072 seconds or more.



·

INF Code: 1141

-

The hybrid control malfunction signal is received for at least 0.072 seconds from hybrid vehicle control ECU assembly.



·

INF Code: 1140

-

Hybrid vehicle control ECU assembly

(VSC malfunction)

-

Skid control ECU (brake booster with master cylinder assembly)


·

INF Code: 1141

-

Hybrid vehicle control ECU assembly

(Brake hold control malfunction)

-

Skid control ECU (brake booster with master cylinder assembly)



·

INF Code: 1140

VSC DTC

HINT:

The DTC is cleared when the conditions return to normal.


·

INF Code: 1141

Brake hold DTC

HINT:

The DTC is cleared when the conditions return to normal.




CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC (HYBRID CONTROL SYSTEM)
a.

Check if a hybrid control system DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK DTC (MOTOR GENERATOR CONTROL SYSTEM)

B

2.CHECK DTC (MOTOR GENERATOR CONTROL SYSTEM)
a.

Check if a motor generator control system DTCs are output.

Powertrain > Motor Generator > Trouble Codes
50001 395

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

3.CHECK DTC (SFI SYSTEM)

B

3.CHECK DTC (SFI SYSTEM)
a.

Check if a SFI system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

4.RECONFIRM DTC

B

4.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1259 and/or C1310 are output. A
DTCs other than C1259 and C1310 are output. B
DTCs are not output. C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

C