Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1211  SLA Linear Solenoid  C1212  SLR Linear Solenoid  C1225  SA1 Solenoid Circuit  C1226  SA2 Solenoid Circuit  


DESCRIPTION

The linear solenoids SLA and SLR control the regulator based on signals from the skid control ECU (brake booster with master cylinder assembly) and produce servo pressure in accordance with the vehicle condition.

When the system is normal, the switching solenoid SGH is opened to allow brake fluid to flow to the stroke simulator when the brake pedal is depressed. When the system is abnormal, the switching solenoid SGH closes to prevent the flow of brake fluid.

When the system is normal, the switching solenoid SSA is closed. When the system is abnormal, the switching solenoid SSA is opened to allow fluid to flow to the brake master cylinder reservoir assembly.

HINT:
·

If the supply voltage decreases, a drop in current may cause DTCs to be stored.

·

DTC C1225 indicates a malfunction related to solenoid SSA, and DTC C1226 indicates a malfunction related to solenoid SGH.



DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1211 SLA Linear Solenoid 21
22
23
24
25
26
·

INF Code: 21

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 22

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 23

-

An excessive current is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 24

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 25

-

A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.


·

INF Code: 26

-

Insufficient current is detected in the solenoid for 0.05 seconds or more.



·

INF Code: 21, 22, 24

-

Brake booster with master cylinder assembly


·

INF Code: 23

-

Supply voltage reduced

-

Brake booster with master cylinder assembly


·

INF Code: 25, 26

-

Brake booster with master cylinder assembly



Electronically controlled brake system DTC
C1212 SLR Linear Solenoid 31
32
33
34
35
36
·

INF Code: 31

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 32

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 33

-

An excessive current is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 34

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 35

-

A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.


·

INF Code: 36

-

Insufficient current is detected in the solenoid for 0.05 seconds or more.



·

INF Code: 31, 32, 34

-

Brake booster with master cylinder assembly


·

INF Code: 33

-

Supply voltage reduced

-

Brake booster with master cylinder assembly


·

INF Code: 35, 36

-

Brake booster with master cylinder assembly



Electronically controlled brake system DTC
C1225 SA1 Solenoid Circuit 41
42
43
44
45
46
·

INF Code: 41

-

Overcurrent is detected in SSA for 0.05 seconds or more.


·

INF Code: 42

-

An open is detected in SSA for 0.05 seconds or more.


·

INF Code: 43

-

Monitoring value of SSA continues to be excessively higher than request value.


·

INF Code: 44

-

Current leakage is detected in SSA for 0.05 seconds or more.


·

INF Code: 45

-

A malfunction in the SSA current monitoring circuit is detected for 0.05 seconds or more.


·

INF Code: 46

-

Monitoring value of SSA continues to be excessively lower than request value.



·

INF Code: 41, 42, 44

-

Brake booster with master cylinder assembly


·

INF Code: 43

-

Supply voltage reduced

-

Brake booster with master cylinder assembly


·

INF Code: 45, 46

-

Brake booster with master cylinder assembly



Electronically controlled brake system DTC
C1226 SA2 Solenoid Circuit 71
72
73
74
75
76
·

INF Code: 71

-

Overcurrent is detected in SGH for 0.05 seconds or more.


·

INF Code: 72

-

An open is detected in SGH for 0.05 seconds or more.


·

INF Code: 73

-

Monitoring value of SGH continues to be excessively higher than request value.


·

INF Code: 74

-

Current leakage is detected in SGH for 0.05 seconds or more.


·

INF Code: 75

-

A malfunction in the SGH current monitoring circuit is detected for 0.05 seconds or more.


·

INF Code: 76

-

Monitoring value of SGH continues to be excessively lower than request value.



·

INF Code: 71, 72, 74

-

Brake booster with master cylinder assembly


·

INF Code: 73

-

Supply voltage reduced

-

Brake booster with master cylinder assembly


·

INF Code: 75, 76

-

Brake booster with master cylinder assembly



Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If a DTC for undervoltage is output, first troubleshoot the power source system.



Result:
Result Proceed to
DTCs C1211, C1212, C1225 and C1226 are not output. A
A DTC related to low voltage is output. B
DTCs C1211, C1212, C1225 and/or C1226 are output. C



A

B

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY