Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1232  Deceleration Sensor  C1243  Deceleration Sensor Stuck  C1245  Abnormal Output in Deceleration Sensor  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2).

The skid control ECU (brake booster with master cylinder assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

HINT:

When a malfunction occurs in the communication line to the yaw rate and acceleration sensor (airbag sensor assembly), U0124 (Lost Communication With Lateral Acceleration Sensor Module) is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


A DTC may be stored if either of the following is detected:

·

Incorrect installation of acceleration sensor (airbag sensor assembly).

·

Abnormal acceleration sensor (airbag sensor assembly) signal.


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1232 Deceleration Sensor 562
563
When the vehicle speed is 10 km/h (6 mph) or more, the acceleration sensor output value does not change for 30 seconds or more.
·

Acceleration sensor (airbag sensor assembly) installed improperly

·

Acceleration sensor (airbag sensor assembly)


ABS DTC
C1243 Deceleration Sensor Stuck 561
564
565
·

INF Code: 561

-

The acceleration sensor output value does not change 16 times or more before the vehicle speed reaches 0 km/h (0 mph) from 30 km/h (19 mph).


·

INF Code: 564

-

The longitudinal and lateral output values of the acceleration sensor are not within the specified range for 60 seconds or more.


·

INF Code: 565

-

The lateral output value of the acceleration sensor is not within the specified range for 60 seconds or more.



·

Acceleration sensor (airbag sensor assembly) installed improperly

·

Acceleration sensor (airbag sensor assembly)


ABS DTC
C1245 Abnormal Output in Deceleration Sensor 581 When the vehicle speed is 30 km/h (19 mph) or more, the difference between the deceleration value from the acceleration sensor and deceleration value calculated from the change in vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Acceleration sensor (airbag sensor assembly) installed improperly

·

Acceleration sensor (airbag sensor assembly)


ABS DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration after clearing previously calibrated data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION


HINT:

When U0124 and/or U0126 is output together with C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073


PROCEDURE

1.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not tilted.



Result:
Proceed to
OK
NG



OK

NG