Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1403  Malfunction in Rear Speed Sensor RH Circuit  C1404  Malfunction in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1415 and C1416.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1415

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1403 Malfunction in Rear Speed Sensor RH Circuit 521
522
527
·

INF Code: 521

-

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.


·

INF Code: 522

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).


·

INF Code: 527

-

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.



·

Skid control sensor wire RH (NO. 1 parking brake wire assembly)

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Speed sensor installed improperly

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Wire harness or connector


ABS DTC
C1404 Malfunction in Rear Speed Sensor LH Circuit 531
532
537
·

INF Code: 531

-

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.


·

INF Code: 532

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).


·

INF Code: 537

-

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.



·

Skid control sensor wire LH (NO. 2 parking brake wire assembly)

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Speed sensor installed improperly

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Wire harness or connector


ABS DTC

PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1403 is output. A
DTC C1404 is output. B



A

2.CHECK REAR SPEED SENSOR RH INSTALLATION

B

6.CHECK REAR SPEED SENSOR LH INSTALLATION
2.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor RH
*a OK
*b NG
*c No Clearance


Check the rear speed sensor RH installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly RH cannot be disassembled, if the rear speed sensor RH needs replacement, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (REAR SPEED SENSOR RH)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

3.READ VALUE USING GTS (REAR SPEED SENSOR RH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
50003 105 3

b.

Check the rear speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
4.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.
C251359C50
0.76,0.906 1.156,1.146 0.396,0.24 2.26,0.917 2.656,1.156 0.396,0.24 0.833,1.979 0.563,2.76 true 1.094,1.979 1.417,2.75 true 2.344,2.052 2.188,2.531 true 2.573,2.052 2.76,2.531 true 0.188,0.177 0.646,0.469 0.458,0.292 10 false *a 0.875,1.219 1.375,1.51 0.5,0.292 10 false *b 2.385,1.219 2.906,1.531 0.521,0.313 10 false *c 0.896,0.948 1.24,1.188 0.344,0.24 10 false u2 2.333,0.948 2.76,1.156 0.427,0.208 10 false uR1 0.438,2.781 1.021,3.021 0.583,0.24 10 false RA- 1.375,2.781 1.969,3.021 0.594,0.24 10 false RA+ 2.073,2.552 2.646,2.771 0.573,0.219 10 false RR+ 2.719,2.552 3.365,2.729 0.646,0.177 10 false RR-
*a Front view of skid control sensor wire RH (NO. 1 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (NO. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
u2-2 (RA+) - uR1-1 (RR+) Always Below 1 Ω
u2-2 (RA+) - uR1-2 (RR-) Always 10 kΩ or higher
u2-2 (RA+) or uR1-1 (RR+) - Body ground Always 10 kΩ or higher
u2-1 (RA-) - uR1-2 (RR-) Always Below 1 Ω
u2-1 (RA-) - uR1-1 (RR+) Always 10 kΩ or higher
u2-1 (RA-) or uR1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 1 PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-7 (RR+) - uR1-1 (RR+) Always Below 1 Ω
A40-7 (RR+) or uR1-1 (RR+) - Body ground Always 10 kΩ or higher
A40-8 (RR-) - uR1-2 (RR-) Always Below 1 Ω
A40-8 (RR-) or uR1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the rear speed sensor RH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor LH
*a OK
*b NG
*c No Clearance


Check the rear speed sensor LH installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly LH cannot be disassembled, if the rear speed sensor LH needs replacement, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (REAR SPEED SENSOR LH)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

7.READ VALUE USING GTS (REAR SPEED SENSOR LH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RL Wheel Speed
50003 105 4

b.

Check the rear speed sensor LH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

8.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
8.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.
C251359C51
0.76,0.906 1.156,1.146 0.396,0.24 2.26,0.917 2.656,1.156 0.396,0.24 0.833,1.979 0.563,2.76 true 1.094,1.979 1.417,2.75 true 2.344,2.052 2.188,2.531 true 2.573,2.052 2.76,2.531 true 0.188,0.177 0.646,0.469 0.458,0.292 10 false *a 0.875,1.219 1.375,1.51 0.5,0.292 10 false *b 2.385,1.219 2.906,1.531 0.521,0.313 10 false *c 0.906,0.948 1.219,1.146 0.313,0.198 10 false v2 2.354,0.958 2.813,1.156 0.458,0.198 10 false vR1 2.708,2.552 3.354,2.729 0.646,0.177 10 false RL- 2.073,2.563 2.646,2.781 0.573,0.219 10 false RL+ 1.365,2.781 1.958,3.021 0.594,0.24 10 false LA+ 0.438,2.792 1.031,3.031 0.594,0.24 10 false LA-
*a Front view of skid control sensor wire LH (NO. 2 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (NO. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
v2-2 (LA+) - vR1-1 (RL+) Always Below 1 Ω
v2-2 (LA+) - vR1-2 (RL-) Always 10 kΩ or higher
v2-2 (LA+) or vR1-1 (RL+) - Body ground Always 10 kΩ or higher
v2-1 (LA-) - vR1-2 (RL-) Always Below 1 Ω
v2-1 (LA-) - vR1-1 (RL+) Always 10 kΩ or higher
v2-1 (LA-) or vR1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-34 (RL+) - vR1-1 (RL+) Always Below 1 Ω
A40-34 (RL+) or vR1-1 (RL+) - Body ground Always 10 kΩ or higher
A40-35 (RL-) - vR1-2 (RL-) Always Below 1 Ω
A40-35 (RL-) or vR1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the rear speed sensor LH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor LH and rear speed sensor rotor LH are incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor LH and rear speed sensor rotor LH need to be replaced, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR