Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1415  Rear Speed Sensor RH Circuit Output  C1416  Rear Speed Sensor LH Circuit Output  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.

HINT:

The output voltage values shown below are for when the vehicle wire harnesses are connected to the skid control ECU (brake booster with master cylinder assembly) and the speed sensors.


C151818E48
1.573,0.854 1.573,0.469 1.573,0.469 1.448,0.469 false 0.531,0.365 1.646,0.74 1.115,0.375 10 false Speed Sensor 4.021,2.115 4.729,2.281 0.708,0.167 10 false Low speed 6.083,1.281 6.448,1.448 0.365,0.167 10 false 1.4 V 6.083,1.625 6.563,1.792 0.479,0.167 10 false 0.7 V 4.99,2.115 5.719,2.281 0.729,0.167 10 false High speed 0.969,2.177 2.26,2.344 1.292,0.167 10 false Speed Sensor Rotor

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1415 Rear Speed Sensor RH Circuit Output 524
543
·

INF Code: 524

-

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.


·

INF Code: 543

-

Either of the following is detected:

(1)

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

(2)

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.




·

Skid control sensor wire RH (NO. 1 parking brake wire assembly)

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Speed sensor installed improperly

·

Wire harness or connector

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC
C1416 Rear Speed Sensor LH Circuit Output 534
544
·

INF Code: 534

-

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.


·

INF Code: 544

-

Either of the following is detected:

(1)

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

(2)

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.




·

Skid control sensor wire LH (NO. 2 parking brake wire assembly)

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Speed sensor installed improperly

·

Wire harness or connector

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC

DTC Detection Conditions: C1415 INF Code: 543
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more. ○ -
At a vehicle speed of 10 km/h (6 mph) or more. - ○
Malfunction Status Noise occurs in the sensor signals of a malfunctioning wheel. ○ -
Noise occurs once per rotor rotation. - ○
Detection Time Detected 75 times or more within 5 seconds 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1416 INF Code: 544
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more. ○ -
At a vehicle speed of 10 km/h (6 mph) or more. - ○
Malfunction Status Noise occurs in the sensor signals of a malfunctioning wheel. ○ -
Noise occurs once per rotor rotation. - ○
Detection Time Detected 75 times or more within 5 seconds 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C351996E14
1.313,0.844 1.771,1.042 0.458,0.198 10 false u2 1.365,0.646 1.823,0.844 0.458,0.198 10 false 2 2.417,0.844 2.875,1.042 0.458,0.198 10 false uR1 2.51,0.635 2.969,0.833 0.458,0.198 10 false 1 2.531,1.344 2.99,1.542 0.458,0.198 10 false 2 2.427,1.552 2.885,1.75 0.458,0.198 10 false uR1 1.313,1.542 1.771,1.74 0.458,0.198 10 false u2 1.354,1.344 1.813,1.542 0.458,0.198 10 false 1 4.323,2.198 4.781,2.396 0.458,0.198 10 false * 4.313,4.604 4.771,4.802 0.458,0.198 10 false * 5.646,0.771 6.104,0.969 0.458,0.198 10 false 7 5.813,0.969 6.271,1.167 0.458,0.198 10 false RR+ 5.646,1.448 6.104,1.646 0.458,0.198 10 false 8 5.813,1.635 6.271,1.833 0.458,0.198 10 false RR- 5.583,3.156 6.042,3.354 0.458,0.198 10 false 34 5.823,3.365 6.281,3.563 0.458,0.198 10 false RL+ 5.583,3.833 6.042,4.031 0.458,0.198 10 false 35 5.813,4.031 6.271,4.229 0.458,0.198 10 false RL- 2.51,3.042 2.969,3.24 0.458,0.198 10 false 1 2.458,3.25 2.917,3.448 0.458,0.198 10 false vR1 2.531,3.74 2.99,3.938 0.458,0.198 10 false 2 2.448,3.948 2.906,4.146 0.458,0.198 10 false vR1 1.333,3.958 1.792,4.156 0.458,0.198 10 false v2 1.354,3.74 1.813,3.938 0.458,0.198 10 false 1 1.333,3.26 1.792,3.458 0.458,0.198 10 false v2 1.365,3.042 1.823,3.24 0.458,0.198 10 false 2 0.021,1.958 1.469,2.594 1.448,0.635 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 1.573,1.958 3.156,2.51 1.583,0.552 10 false Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly) 0.021,4.354 1.438,4.917 1.417,0.563 10 false Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH) 1.594,4.354 3.167,4.948 1.573,0.594 10 false Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly) 3.521,5.313 4.417,5.552 0.896,0.24 10 false *: Shielded 5.094,4.948 5.552,5.146 0.458,0.198 10 false A40 5.073,5.125 7.135,5.5 2.063,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.031,0.854 2.49,1.052 0.458,0.198 10 false RR+ 1.625,0.854 2.083,1.052 0.458,0.198 10 false RA+ 0.865,0.854 1.323,1.052 0.458,0.198 10 false RA+ 2.042,1.563 2.5,1.76 0.458,0.198 10 false RR- 1.625,1.563 2.083,1.76 0.458,0.198 10 false RA- 0.885,1.563 1.344,1.76 0.458,0.198 10 false RA- 2.063,3.26 2.521,3.458 0.458,0.198 10 false RL+ 1.625,3.26 2.083,3.458 0.458,0.198 10 false LA+ 0.885,3.26 1.344,3.458 0.458,0.198 10 false LA+ 2.063,3.948 2.521,4.146 0.458,0.198 10 false RL- 1.625,3.948 2.083,4.146 0.458,0.198 10 false LA- 0.896,3.958 1.354,4.156 0.458,0.198 10 false LA-

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1415 is output. A
DTC C1416 is output. B



A

2.READ VALUE USING GTS (MOMENTARY INTERRUPTION)

B

9.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
2.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Sensor Voltage Open
50003 105 296

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (REAR SPEED SENSOR RH)

NG

5.CHECK REAR SPEED SENSOR RH INSTALLATION
3.READ VALUE USING GTS (REAR SPEED SENSOR RH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
50003 105 3

b.

Check the rear speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR RH INSTALLATION
4.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1415 is not output. A
DTC C1415 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor RH
*a OK
*b NG
*c No Clearance


Turn the power switch off.


b.

Check the rear speed sensor RH installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly RH cannot be disassembled, if the rear speed sensor RH needs replacement, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

6.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.
C251359C50
0.76,0.906 1.156,1.146 0.396,0.24 2.26,0.917 2.656,1.156 0.396,0.24 0.833,1.979 0.563,2.76 true 1.094,1.979 1.417,2.75 true 2.344,2.052 2.188,2.531 true 2.573,2.052 2.76,2.531 true 0.188,0.177 0.646,0.469 0.458,0.292 10 false *a 0.875,1.219 1.375,1.51 0.5,0.292 10 false *b 2.385,1.219 2.906,1.531 0.521,0.313 10 false *c 0.896,0.948 1.24,1.188 0.344,0.24 10 false u2 2.333,0.948 2.76,1.156 0.427,0.208 10 false uR1 0.438,2.781 1.021,3.021 0.583,0.24 10 false RA- 1.375,2.781 1.969,3.021 0.594,0.24 10 false RA+ 2.073,2.552 2.646,2.771 0.573,0.219 10 false RR+ 2.719,2.552 3.365,2.729 0.646,0.177 10 false RR-
*a Front view of skid control sensor wire RH (NO. 1 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Remove the skid control sensor wire RH (NO. 1 parking brake wire assembly).


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
u2-2 (RA+) - uR1-1 (RR+) Always Below 1 Ω
u2-2 (RA+) - uR1-2 (RR-) Always 10 kΩ or higher
u2-2 (RA+) or uR1-1 (RR+) - Body ground Always 10 kΩ or higher
u2-1 (RA-) - uR1-2 (RR-) Always Below 1 Ω
u2-1 (RA-) - uR1-1 (RR+) Always 10 kΩ or higher
u2-1 (RA-) or uR1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 1 PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-7 (RR+) - uR1-1 (RR+) Always Below 1 Ω
A40-7 (RR+) or uR1-1 (RR+) - Body ground Always 10 kΩ or higher
A40-8 (RR-) - uR1-2 (RR-) Always Below 1 Ω
A40-8 (RR-) or uR1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C380198C11
1.49,0.844 1.906,1.146 0.417,0.302 2.219,2.677 1.875,2.01 true 0.385,0.354 0.698,0.552 0.313,0.198 10 false *a 1.583,0.917 1.896,1.115 0.313,0.198 10 false uR1 2.125,2.719 2.552,2.938 0.427,0.219 10 false RR+
*a Front view of wire harness connector
(to Skid Control Sensor Wire RH (NO. 1 Parking Brake Wire Assembly))


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
uR1-1 (RR+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the rear speed sensor RH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RL Speed Sensor Voltage Open
50003 105 297

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (REAR SPEED SENSOR LH)

NG

12.CHECK REAR SPEED SENSOR LH INSTALLATION
10.READ VALUE USING GTS (REAR SPEED SENSOR LH)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RL Wheel Speed
50003 105 4

b.

Check the rear speed sensor LH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

11.RECONFIRM DTC

NG

12.CHECK REAR SPEED SENSOR LH INSTALLATION
11.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1416 is not output. A
DTC C1416 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

12.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor LH
*a OK
*b NG
*c No Clearance


Turn the power switch off.


b.

Check the rear speed sensor LH installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly LH cannot be disassembled, if the rear speed sensor LH needs replacement, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

13.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

13.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.
C251359C51
0.76,0.906 1.156,1.146 0.396,0.24 2.26,0.917 2.656,1.156 0.396,0.24 0.833,1.979 0.563,2.76 true 1.094,1.979 1.417,2.75 true 2.344,2.052 2.188,2.531 true 2.573,2.052 2.76,2.531 true 0.188,0.177 0.646,0.469 0.458,0.292 10 false *a 0.875,1.219 1.375,1.51 0.5,0.292 10 false *b 2.385,1.219 2.906,1.531 0.521,0.313 10 false *c 0.906,0.948 1.219,1.146 0.313,0.198 10 false v2 2.354,0.958 2.813,1.156 0.458,0.198 10 false vR1 2.708,2.552 3.354,2.729 0.646,0.177 10 false RL- 2.073,2.563 2.646,2.781 0.573,0.219 10 false RL+ 1.365,2.781 1.958,3.021 0.594,0.24 10 false LA+ 0.438,2.792 1.031,3.031 0.594,0.24 10 false LA-
*a Front view of skid control sensor wire LH (NO. 2 parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Remove the skid control sensor wire LH (NO. 2 parking brake wire assembly).


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
v2-2 (LA+) - vR1-1 (RL+) Always Below 1 Ω
v2-2 (LA+) - vR1-2 (RL-) Always 10 kΩ or higher
v2-2 (LA+) or vR1-1 (RL+) - Body ground Always 10 kΩ or higher
v2-1 (LA-) - vR1-2 (RL-) Always Below 1 Ω
v2-1 (LA-) - vR1-1 (RL+) Always 10 kΩ or higher
v2-1 (LA-) or vR1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

14.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-34 (RL+) - vR1-1 (RL+) Always Below 1 Ω
A40-34 (RL+) or vR1-1 (RL+) - Body ground Always 10 kΩ or higher
A40-35 (RL-) - vR1-2 (RL-) Always Below 1 Ω
A40-35 (RL-) or vR1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C380198C12
1.49,0.844 1.906,1.146 0.417,0.302 2.219,2.677 1.875,2.01 true 0.385,0.354 0.698,0.552 0.313,0.198 10 false *a 1.583,0.906 1.896,1.104 0.313,0.198 10 false vR1 2.125,2.719 2.552,2.938 0.427,0.219 10 false RL+
*a Front view of wire harness connector
(to Skid Control Sensor Wire LH (NO. 2 Parking Brake Wire Assembly))


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
vR1-1 (RL+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the rear speed sensor LH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

The rear speed sensor LH and rear speed sensor rotor LH are incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor LH and rear speed sensor rotor LH need to be replaced, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY