Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1417  IG1 Voltage Supply too High  


DESCRIPTION

If a malfunction is detected in the power source circuit, the skid control ECU (brake booster with master cylinder assembly) stores DTC C1417 and prohibits operation of ABS, brake assist, regenerative brake cooperative control, etc.

DTC C1417 is stored if an excessive ECU voltage due to a malfunction in the auxiliary battery, charging circuit, etc. is detected, and is cleared when the ECU voltage returns to normal.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1417 IG1 Voltage Supply too High 553 The internal voltage of the skid control ECU (brake booster with master cylinder assembly) is 16.44 V or more for 0.8 seconds or more.
·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Wire harness or connector

·

Improperly connected connector, deformation or corrosion of terminals

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C378330C05
0.302,0.698 0.708,0.979 0.406,0.281 2.188,1.896 2.646,1.01 true 1.417,1.896 1.135,1.021 true 1.625,1.615 1.406,0.75 true 2,1.615 2.063,0.729 true 2.677,2.896 2.51,2.26 true 0.385,0.771 0.844,0.969 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.969,0.833 1.583,1.031 0.615,0.198 10 false +BI1 1.229,0.552 1.844,0.75 0.615,0.198 10 false +BI2 1.99,0.552 2.604,0.75 0.615,0.198 10 false IG2 2.583,0.833 3.042,1.031 0.458,0.198 10 false IG1 2.635,2.906 2.948,3.104 0.313,0.198 10 false BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-15 (+BI1) - Body ground Always 11 to 14 V
A40-5 (+BI2) - Body ground Always 11 to 14 V
A40-52 (BS) - Body ground Always 11 to 14 V
A40-23 (IG1) - Body ground Power switch on (IG) 11 to 14 V
A40-9 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the power switch off.


e.

Turn the power switch on (READY).


f.

Perform a road test.


g.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1417 is not output. A
DTC C1417 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY