Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2017.09–2018.04
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1425  Open in Stop Switch Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.

The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1425 Open in Stop Switch Circuit 231 An open stop light switch circuit continues for 10 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake booster with master cylinder assembly)

·

Stop light circuit


Electronically controlled brake system DTC

WIRING DIAGRAM

C425145E01
5.542,1.26 6.156,1.458 0.615,0.198 10 false STP2 5.521,2.26 6.135,2.458 0.615,0.198 10 false STPO 5.542,3.354 6.156,3.552 0.615,0.198 10 false STP 5.281,3.115 5.896,3.313 0.615,0.198 10 false 12 5.281,2.021 5.896,2.219 0.615,0.198 10 false 22 5.281,1.031 5.896,1.229 0.615,0.198 10 false 37 5.083,3.948 5.698,4.146 0.615,0.198 10 false A40 5.073,4.104 7.135,4.479 2.063,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.073,4.219 4.885,4.573 0.813,0.354 10 false to Stop Light Circuit 3.75,1.031 4.365,1.229 0.615,0.198 10 false 3 3.771,2.021 4.385,2.219 0.615,0.198 10 false 4 3.781,3.115 4.396,3.313 0.615,0.198 10 false 1 3.396,3.365 4.01,3.563 0.615,0.198 10 false OUT 3.396,2.26 4.01,2.458 0.615,0.198 10 false ACC 3.573,1.281 3.76,1.5 0.188,0.219 10 false L 1.813,1.385 2.104,1.615 0.292,0.229 10 false 7 2,1.615 2.271,1.906 0.271,0.292 10 false B 1.802,3.115 2.052,3.313 0.25,0.198 10 false 2 1.99,3.354 2.604,3.552 0.615,0.198 10 false GND 2.073,3.802 2.385,4.021 0.313,0.219 10 false A37 2.063,3.969 3.854,4.177 1.792,0.208 10 false Stop Light Switch Assembly 1.094,1.667 1.531,1.865 0.438,0.198 10 false STOP 1.031,1.396 1.208,1.594 0.177,0.198 10 false 1 1.406,1.396 1.615,1.563 0.208,0.167 10 false 2 1.865,0.281 3.302,0.5 1.438,0.219 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.


Result:
Result Proceed to
All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. A
All stop lights do not illuminate when the brake pedal is depressed. B
One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. C



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)

C

6.CHECK STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

b.

Check the value of Stop Light SW when the brake pedal is depressed.


Result:
Result Proceed to
The value of Stop Light SW is ON. A
Other than above. B



A

3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION

B

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION
a.
C415041C24
1.479,0.427 1.844,0.667 0.365,0.24 2.323,1.635 2.073,1.125 true 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 1.542,0.458 1.906,0.667 0.365,0.208 10 false A37 2.219,1.667 2.625,1.875 0.406,0.208 10 false OUT
*a Component with harness connected
(Stop Light Switch Assembly)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-1 (OUT) - Body ground
·

Power switch on (IG)

·

The headlights are on

·

The blower motor switch is in the HI position

·

The rear window defogger is turned on

·

Stop light switch assembly off (Brake pedal released)


1.5 V or less



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

6.CHECK STOP LIGHT SWITCH ASSEMBLY
4.CLEAR DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the power switch off.


b.

Turn the power switch on (READY).


c.

Perform a road test.


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.CHECK STOP LIGHT SWITCH ASSEMBLY
a.
E360372C60
1.417,0.219 1.917,0.5 0.5,0.281 0.677,1.594 1.094,1.177 true 0.115,0.135 0.427,0.333 0.313,0.198 10 false *a 1.531,0.281 1.844,0.479 0.313,0.198 10 false A37 0.417,1.615 0.729,1.813 0.313,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A37 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-1 (OUT) - Body ground Stop light switch assembly off (Brake pedal released) 1.5 V or less



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

7.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
7.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.
E360372C60
1.417,0.219 1.917,0.5 0.5,0.281 0.677,1.594 1.094,1.177 true 0.115,0.135 0.427,0.333 0.313,0.198 10 false *a 1.531,0.281 1.844,0.479 0.313,0.198 10 false A37 0.417,1.615 0.729,1.813 0.313,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-1 (OUT) - Body ground Stop light switch assembly off (Brake pedal released) 1.5 V or less



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

8.CHECK FOR SHORT TO +B IN STP CIRCUIT
8.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses, connectors and stop lights).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C378330C10
0.438,0.698 0.844,0.979 0.406,0.281 2.281,1.615 2.583,0.969 true 2.521,0.792 2.979,0.99 0.458,0.198 10 false STP 0.531,0.75 0.99,0.948 0.458,0.198 10 false A40 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-12 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)
a.

Check that there is no open in the wire harnesses and connectors from terminal OUT of the stop light switch assembly to the stop lights.


OK:

No open.


Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR