Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1436  Malfunction in Yaw Rate Sensor  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2).

When the skid control ECU (brake booster with master cylinder assembly) detects improper installation of the yaw rate and acceleration sensor (airbag sensor assembly) or an abnormality in the difference between the yaw rate sensor value and the control value estimated based on the acceleration sensor, steering angle sensor and speed sensor signals, DTC C1436 is stored.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1436 Malfunction in Yaw Rate Sensor 713
714
Either of the following is detected:
1.

With the vehicle stationary, the yaw rate sensor output value is not 0 deg/s.

2.

Abnormal comparison value.


·

Yaw rate sensor (airbag sensor assembly) installed improperly

·

Yaw rate sensor (airbag sensor assembly)


VSC DTC

DTC Detection Conditions: C1436 INF Codes: 713 and/or 714
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition The vehicle is stopped. ○ -
Malfunction Status The yaw rate and acceleration sensor output value is not 0 deg/s. ○ -
Abnormal comparison value. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration after clearing previously calibrated data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION


PROCEDURE

1.READ VALUE USING GTS (YAW RATE SENSOR)
a.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw Rate Sensor Yaw rate sensor 1 Min.: -128 degrees/s, Max.: 127 degrees/s Vehicle stationary: 0 degrees/s
Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s
-
Yaw Rate Sensor2 Yaw rate sensor 2 Min.: -128 degrees/s, Max.: 127 degrees/s Vehicle stationary: 0 degrees/s
Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Yaw Rate Sensor
Yaw Rate Sensor2
50003 105 24,25

b.

Check the yaw rate sensor output value displayed on the GTS.


Result:
Result Proceed to
NG (The yaw rate sensor (airbag sensor assembly) output value is 0 deg/s when the vehicle is stationary, but the value fluctuates when turning.) A
NG (The yaw rate sensor (airbag sensor assembly) output value is not 0 deg/s when the vehicle is stationary.) B
OK C



A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

C

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the power switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not tilted.



Result:
Proceed to
OK
NG



OK

NG