Home › Engine / Hybrid System › A25A-FXS (COOLING) › FLOW SHUTTING VALVE
RM33C0E _51 Engine / Hybrid System _065424 A25A-FXS COOLING _0328476 FLOW SHUTTING VALVE A

A25A-FXS COOLING  FLOW SHUTTING VALVE  INSTALLATION  


PROCEDURE

Hide 16260 1.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A406309C02
1.031,3.917 1.031,3.354 false 0.969,3.948 1.281,4.104 0.313,0.156 10 false *a 3,2.917 3.313,3.073 0.313,0.156 10 false *b 3,3.573 3.313,3.729 0.313,0.156 10 false *b
*a Paint Mark
*b 45° (Tabs of Clip Installation Area)


Connect the flow shutting valve (water by-pass hose assembly) to the water by-pass outlet sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the water by-pass outlet sub-assembly.

·

Make sure that the tabs of the clip are within the area shown in the illustration.




b.

Connect the flow shutting valve (water by-pass hose assembly) with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

Connect the No. 2 water by-pass pipe sub-assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.

Connect the inlet heater hose connector to the flow shutting valve (water by-pass hose assembly).

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the water lines.


i.
A403462C01
1.01,0.979 1.438,0.979 false 1.875,0.969 2.302,0.969 false 1.021,1.354 1.448,1.354 false 1.844,1.365 2.281,1.917 2.281,1.917 2.594,1.917 false 0.813,0.885 1.125,1.042 0.313,0.156 10 false *a 0.833,1.271 1.146,1.427 0.313,0.156 10 false *b 2.365,0.896 2.677,1.052 0.313,0.156 10 false *a 2.635,1.844 2.948,2 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusions of the inlet heater hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and push them together until the inlet heater hose connector makes a "click" sound.


ii.
A406310C02
1.573,1.156 1.844,0.594 1.844,0.594 2.052,0.594 false 2.094,0.531 2.375,0.729 0.281,0.198 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


iii.

Check that the flow shutting valve (water by-pass hose assembly) and inlet heater hose connector are securely connected by pulling on them.



e.

Connect the outlet heater hose connector to the No. 2 water by-pass pipe sub-assembly.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the water lines.


i.
A403463C01
1.052,1.156 1.573,1.156 false 0.99,0.365 1.219,0.365 1.219,0.365 1.521,0.792 false 0.875,1.063 1.188,1.219 0.313,0.156 10 false *a 0.823,0.281 1.135,0.438 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater hose connector and push them together until the outlet heater hose connector makes a "click" sound.


ii.
A406311C02
1.302,1.552 1.521,1.552 1.521,1.552 1.813,1.271 false 1.125,1.479 1.375,1.688 0.25,0.208 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


iii.

Check that the No. 2 water by-pass pipe sub-assembly and outlet heater hose connector are securely connected by pulling on them.



f.

Connect the flow shutting valve (water by-pass hose assembly) connector.


Hide G9200 2.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 3.ADD ENGINE COOLANT (for Engine)

Hide 4.INSPECT FOR COOLANT LEAK (for Engine)