Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2017.09–2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0328967 DYNAMIC RADAR CRUISE CONTROL SYSTEM Y

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Perform the following procedure to troubleshoot the dynamic radar cruise control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT AUXILIARY BATTERY VOLTAGE
2.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY*
3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY*


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Turn the cruise control main switch on.


g.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.


h.

Check the amount of misalignment and make a note.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 220 4405

i.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.


j.

Check the amount of offset and make a note.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Offset Reading
50005 220 4406

k.

Calculate the "Dealership Axis Offset Angle (with On-line Calibration Angle)" using the values "Front Beam Axis Misalignment Reading" and "Front Beam Axis Offset Reading".

i.

"Dealership Axis Offset Angle (with On-line Calibration Angle)" = "Front Beam Axis Misalignment Reading" - "Front Beam Axis Offset Reading"

Standard:
Dealership Axis Offset Angle (with On-line Calibration Angle):
Vertical -5.2 to 5.2 deg.
Horizontal -0.6 to 0.6 deg.




Result:
Result Proceed to
The dealership axis offset angle (with on-line calibration angle) is within the specified range. A
The dealership axis offset angle (with on-line calibration angle) is not within the specified range. B



A

4.CHECK CAN COMMUNICATION SYSTEM*

B

13.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check that the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

OK:

CAN communication system is functioning normally.



Result:
Proceed to
OK
NG



OK

5.CHECK METER / GAUGE SYSTEM*

NG

5.CHECK METER / GAUGE SYSTEM*
a.

Check for DTCs.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
Meter/gauge system DTCs are not output A
Meter/gauge system DTCs are output B



A

6.CHECK ELECTRONICALLY CONTROLLED BRAKE SYSTEM*

B

6.CHECK ELECTRONICALLY CONTROLLED BRAKE SYSTEM*
a.

Use the GTS to check if the electronically controlled brake system is functioning normally.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs is not output A
Electronically controlled brake system DTCs are output B



A

7.CHECK ELECTRIC PARKING BRAKE SYSTEM*

B

7.CHECK ELECTRIC PARKING BRAKE SYSTEM*
a.

Use the GTS to check if the electric parking brake system is functioning normally.

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
Electric parking brake system DTCs are not output A
Electric parking brake system DTCs are output B



A

8.CHECK FOR DTCs*

B

8.CHECK FOR DTCs*
a.

Check for DTCs and note any codes that are output.

Powertrain > Cruise Control > Trouble Codes
50001 399
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

b.

Clear the DTCs.

Powertrain > Cruise Control > Clear DTCs
50002 399
Powertrain > Radar Cruise2 > Clear DTCs
50002 197

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

Powertrain > Cruise Control > Trouble Codes
50001 399
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

9.PROBLEM SYMPTOMS TABLE

B

9.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

10.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

11.ADJUST, REPAIR OR REPLACE
NOTICE:

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

12.CONFIRMATION TEST
12.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

13.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*