Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2017.09–2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0329029 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the hybrid vehicle control ECU assembly. When the hybrid vehicle control ECU assembly receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light switch signal circuit. The cancellation condition occurs when voltage is applied to the terminal STP. When the brake pedal is depressed, voltage is applied to the terminal STP of the hybrid vehicle control ECU assembly through the STOP fuse and the stop light switch assembly, and the hybrid vehicle control ECU assembly cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure When the power switch is on (IG) and the cruise control system is operating, the voltage of the STP and ST1- terminals of the hybrid vehicle control ECU assembly are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

Hybrid vehicle control ECU assembly



WIRING DIAGRAM

A412334E01
0.292,1.052 2.583,1.25 2.292,0.198 10 false from J/B-B Fuse 0.01,1.531 1.333,1.74 1.323,0.208 10 false from IG2-NO. 2 Relay 2.281,1.219 4.573,1.417 2.292,0.198 10 false STOP 2.052,1.75 4.344,1.948 2.292,0.198 10 false ECU-IG2 NO. 3 2.969,2.458 5.26,2.656 2.292,0.198 10 false Stop Light Switch Assembly 2.635,2.469 4.927,2.667 2.292,0.198 10 false A37 3.438,2.083 3.885,2.344 0.448,0.26 10 false GND 3.438,1.563 3.885,1.823 0.448,0.26 10 false B 3.448,1.063 3.896,1.323 0.448,0.26 10 false B 4.031,0.938 4.479,1.198 0.448,0.26 10 false L 4.031,1.729 4.479,1.99 0.448,0.26 10 false L 3.26,0.938 3.708,1.198 0.448,0.26 10 false 7 3.271,1.458 3.719,1.719 0.448,0.26 10 false 6 3.281,1.958 3.729,2.219 0.448,0.26 10 false 2 4.219,0.844 4.667,1.104 0.448,0.26 10 false 3 4.219,1.635 4.667,1.896 0.448,0.26 10 false 5 5.385,2.458 6.792,2.865 1.406,0.406 10 false Hybrid Vehicle Control ECU Assembly 5.135,1.729 5.583,1.99 0.448,0.26 10 false A29 5.146,0.948 5.594,1.208 0.448,0.26 10 false A28 5.552,0.844 6,1.104 0.448,0.26 10 false STP 5.552,1.625 6,1.885 0.448,0.26 10 false ST1- 5.177,0.719 5.625,0.979 0.448,0.26 10 false 15 5.188,1.521 5.635,1.781 0.448,0.26 10 false 28 2.781,3.885 4.833,4.271 2.052,0.385 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.448,3.885 4.74,4.083 2.292,0.198 10 false A40 3.792,3.49 4.271,3.708 0.479,0.219 10 false STP2 4.229,3.375 4.708,3.594 0.479,0.219 10 false 37 5.354,3.375 5.833,3.594 0.479,0.219 10 false 25 5.615,3.49 6.094,3.708 0.479,0.219 10 false STP1 5.271,3.875 6.833,4.26 1.563,0.385 10 false Certification ECU (Smart Key ECU Assembly) 5.042,3.875 5.521,4.094 0.479,0.219 10 false R8

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
A395526C06
1.479,0.302 1.875,0.521 0.396,0.219 0.792,1.823 1.292,1.156 true 1.469,1.844 1.969,1.177 true 2.26,1.156 2.76,0.49 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.615,1.844 1.073,2.042 0.458,0.198 10 false GND 1.427,1.844 1.885,2.042 0.458,0.198 10 false B 2.823,0.427 3.281,0.625 0.458,0.198 10 false B 1.552,0.344 2.01,0.542 0.458,0.198 10 false A37
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A37 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-7 (B) - Body ground Always 11 to 14 V
A37-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A37-6 (B) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A28 and A29 hybrid vehicle control ECU assembly connectors.


b.

Disconnect the A37 stop light switch assembly connector.


c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-28 (ST1-) - A37-5 (L) Always Below 1 Ω
A28-15 (STP) - A37-3 (L) Always Below 1 Ω
A29-28 (ST1-) or A37-5 (L) - Body ground Always 10 kΩ or higher
A28-15 (STP) or A37-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR