Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2017.09–2021.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A2  Engine Switch/Power Switch Malfunction  


DESCRIPTION

When the power switch is turned on (IG), power is supplied to the parking brake ECU (brake actuator assembly). This DTC is stored if IG power source voltage is not supplied to the parking brake ECU (brake actuator assembly) when communication with other ECUs is established.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A2 Engine Switch/Power Switch Malfunction Both of following conditions are met:
1.

Power switch on (IG)

2.

When hybrid vehicle control ECU assembly communicates with main body ECU (multiplex network body ECU) via CAN communication, IG power supply voltage is not received for approximately 15 seconds.


·

Wire harness or connector

·

IG power source circuit

·

Parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C381928E02
1.406,0.917 3.24,1.115 1.833,0.198 10 false ECU-IG1 NO. 3 2,1.885 2.917,2.083 0.917,0.198 10 false to CAN 3.531,0.771 3.844,0.969 0.313,0.198 10 false IG 4.531,0.771 5.146,0.969 0.615,0.198 10 false EGND 5.042,0.667 5.198,0.865 0.156,0.198 10 false 2 3.417,2.5 3.833,2.667 0.417,0.167 10 false A44 3.417,2.667 5.094,3.573 1.677,0.906 10 false Parking Brake ECU (Brake Actuator Assembly) 0.958,3.24 3.083,3.583 2.125,0.344 10 false : CAN Communication Line 3.24,0.667 3.552,0.865 0.313,0.198 10 false 26

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

The parking brake indicator light blinks (red) when the power switch is turned on (IG) after replacing the parking brake ECU (brake actuator assembly). Operate the electric parking brake switch (electric parking brake switch assembly) to turn off the parking brake indicator light (red).



PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Switch IG power source status OFF or ON OFF: IG power source voltage is not input to skid control ECU (brake booster with master cylinder assembly)
ON: IG power source voltage is input to skid control ECU (brake booster with master cylinder assembly)
-
Chassis > Electric Parking Brake > Data List
Tester Display
IG Switch
50003 184 601
Result:
Proceed to
OK
NG




OK

2.CHECK DTC

NG

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - POWER SOURCE AND BODY GROUND)
2.CHECK DTC
a.

Clear the DTCs.

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Check for DTCs.

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - POWER SOURCE AND BODY GROUND)
a.
C379767C22
1.49,0.688 1.948,0.979 0.458,0.292 1,2.75 1,1.75 true 2.021,2.75 2.021,2.031 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.594,0.74 1.906,0.938 0.313,0.198 10 false A44 0.844,2.792 1.458,3 0.615,0.208 10 false EGND 1.979,2.792 2.594,3 0.615,0.208 10 false IG
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Disconnect the A44 parking brake ECU (brake actuator assembly) connectors.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-26 (IG) - Body ground Power switch on (IG) 8 to 16 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A44-2 (EGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR IG POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR