Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2017.09–2021.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C367786E07
0.625,0.698 1.625,0.875 1,0.177 10 false EPB NO. 1 0.49,1.292 1.625,1.521 1.135,0.229 10 false ECU-IG1 NO. 3 2.76,0.438 2.948,0.688 0.188,0.25 10 false 9 2.823,1.531 3.135,1.729 0.313,0.198 10 false A44 2.708,1.021 2.969,1.24 0.26,0.219 10 false 26 2.823,1.708 4.49,2.26 1.667,0.552 10 false Parking Brake ECU (Brake Actuator Assembly) 3,1.135 3.313,1.333 0.313,0.198 10 false IG 2.99,0.542 3.427,0.729 0.438,0.188 10 false BEPB 5.292,1.302 7.156,1.521 1.865,0.219 10 false Combination Meter Assembly 0.917,2.417 2.75,2.625 1.833,0.208 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

The parking brake indicator light blinks (red) when the power switch is turned on (IG) after replacing the parking brake ECU (brake actuator assembly). Operate the electric parking brake switch (electric parking brake switch assembly) to turn off the parking brake indicator light (red).



HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light (red) on the combination meter may be malfunctioning.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.VEHICLE OPERATION CHECK

B

2.VEHICLE OPERATION CHECK
a.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Lock and release operation is normal and parking brake indicator light turns off or blinks (red) A
Lock and release operation is malfunctioning and parking brake indicator light illuminates (red) or turns off according to switch operation B
Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks (red) C



A

3.PERFORM GTS (PARKING BRAKE LIGHT)

B

INSPECT REAR BRAKE

C

5.CHECK HARNESS AND CONNECTOR (BEPB CIRCUIT)
3.PERFORM GTS (PARKING BRAKE LIGHT)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Chassis > Electric Parking Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PKB Light Parking brake indicator light (red) ON or OFF
·

Vehicle stopped

·

Power switch on (IG)


Chassis > Electric Parking Brake > Active Test
Tester Display
PKB Light
50004 184 29

g.

Select the Data List on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake Light Parking brake indicator light (red) output signal OFF, Light or Blink OFF: Parking brake indicator light (red) turns off
Light: Parking brake indicator light (red) illuminates
Blink: Parking brake indicator light (red) flashes
-
Chassis > Electric Parking Brake > Data List
Tester Display
Parking Brake Light
50003 184 45

h.

Check the operating condition of the parking brake indicator light (red) when operating it using the GTS.

Result:
Result Proceed to
The value of the Data List item does not change in accordance with the Active Test. A
The value of the Data List item changes in accordance with the Active Test. B




A

B

4.INSPECT COMBINATION METER ASSEMBLY
4.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Park Warning
50004 409 108

b.

Check the combination meter assembly.

OK:

Parking brake indicator light (red) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (BEPB CIRCUIT)
a.

Turn the power switch off.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.
C379767C17
1.542,0.771 1.958,1.01 0.417,0.24 2.385,2.667 2.385,1.74 true 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.625,0.802 1.938,1 0.313,0.198 10 false A44 2.25,2.708 2.75,2.948 0.5,0.24 10 false BEPB
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-9 (BEPB) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Turn the power switch off.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.
C379767C18
1.479,0.74 1.927,0.99 0.448,0.25 2.021,2.771 2.021,2.021 false 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 1.583,0.771 1.896,0.969 0.313,0.198 10 false A44 1.979,2.792 2.292,2.99 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A44-26 (IG) - Body ground Power switch on (IG) 8 to 16 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR