Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "ECM (Engine)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "ECM (Engine)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

ECM main line or connector

·

ECM branch line or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C434931E01
0.135,2.323 0.75,2.521 0.615,0.198 10 false A67 0.458,2.323 2.531,2.625 2.073,0.302 10 false No. 2 CAN Junction Connector 1.771,0.208 2.385,0.406 0.615,0.198 10 false 3 1.74,0.781 2.354,0.979 0.615,0.198 10 false 14 1.729,1.365 2.344,1.563 0.615,0.198 10 false 11 1.729,1.938 2.344,2.135 0.615,0.198 10 false 22 5.469,0.198 5.771,0.594 0.302,0.396 10 false 7 5.729,0.323 6.323,0.594 0.594,0.271 10 false CAN+ 5.448,0.792 5.75,1.188 0.302,0.396 10 false 17 5.74,0.906 6.333,1.177 0.594,0.271 10 false CAN- 5.49,1.375 5.792,1.771 0.302,0.396 10 false 8 5.448,1.948 5.75,2.344 0.302,0.396 10 false 18 5.719,1.365 6.313,1.635 0.594,0.271 10 false CANH 5.729,2.198 6.323,2.469 0.594,0.271 10 false CANL 1.427,2.771 2.979,3.104 1.552,0.333 10 false from Auxiliary Battery 3.781,2.635 4.969,2.958 1.188,0.323 10 false EFI-MAIN NO. 4 5.521,2.656 5.823,3.052 0.302,0.396 10 false 1 5.729,2.781 6.323,3.052 0.594,0.271 10 false BATT 3.781,3.125 4.969,3.448 1.188,0.323 10 false ECU-IG2 NO. 1 1.438,3.281 2.792,3.635 1.354,0.354 10 false from IG2 NO. 1 Relay 5.75,3.292 6.344,3.563 0.594,0.271 10 false IGSW 5.49,3.156 5.792,3.552 0.302,0.396 10 false 2 1.073,3.75 2.99,4.073 1.917,0.323 10 false from EFI-MAIN NO. 1 Relay 5.51,3.625 5.813,4.021 0.302,0.396 10 false 9 5.438,4.073 5.74,4.469 0.302,0.396 10 false 35 5.75,3.74 6.344,4.01 0.594,0.271 10 false +B 5.729,4.198 6.323,4.469 0.594,0.271 10 false +B2 1.198,4.615 2.844,5.042 1.646,0.427 10 false to EFI-MAIN NO. 1 Relay 5.427,4.49 5.729,4.885 0.302,0.396 10 false 15 5.74,4.604 6.333,4.875 0.594,0.271 10 false MREL 5.448,6.479 5.75,6.875 0.302,0.396 10 false 45 5.729,6.604 6.031,7 0.302,0.396 10 false EC 5.448,4.854 5.75,5.25 0.302,0.396 10 false 10 5.458,5.313 5.76,5.708 0.302,0.396 10 false 36 5.458,5.771 5.76,6.167 0.302,0.396 10 false 54 5.729,4.958 6.031,5.354 0.302,0.396 10 false E1 5.75,5.417 6.052,5.813 0.302,0.396 10 false E2 5.729,5.896 6.24,6.156 0.51,0.26 10 false E1D1 5.802,7.167 6.177,7.458 0.375,0.292 10 false A22 6.115,7.167 6.49,7.458 0.375,0.292 10 false ECM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE AND BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A22 ECM connector.


c.
C381742C03
1.542,0.104 1.938,0.333 0.396,0.229 1.74,2.958 1.906,2.958 1.906,2.958 1.906,1.458 true 2.188,2.958 2.021,2.958 2.021,2.958 2.021,1.458 true 1.74,0.438 1.906,0.438 1.906,0.438 1.906,1.271 true 2.177,0.438 2.01,0.438 2.01,0.438 2.01,1.271 true 1.615,0.135 2.073,0.333 0.458,0.198 10 false A22 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.323,0.375 1.781,0.573 0.458,0.198 10 false CAN+ 2.25,0.365 2.708,0.563 0.458,0.198 10 false CANH 1.302,2.896 1.76,3.094 0.458,0.198 10 false CAN- 2.26,2.896 2.719,3.094 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-7 (CAN+) - A22-17 (CAN-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A22-8 (CANH) - A22-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (No. 2 CAN junction connector main line) B
NG (No. 2 CAN junction connector branch line) C



A

2.CHECK ECM POWER SOURCE CIRCUIT

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM)

C

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (ECM)

2.CHECK ECM POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)