Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Restraints Occupant Classification System Module Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Restraints Occupant Classification System Module Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Occupant Detection" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Occupant Detection" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Occupant Detection" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Restraints Occupant Classification System Module Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Occupant detection ECU branch line or connector

·

Power source circuit of occupant detection ECU

·

Occupant detection ECU ground circuit

·

Occupant detection ECU



WIRING DIAGRAM

C350998E48
0.271,1.844 0.729,2.042 0.458,0.198 10 false R99 0.583,1.844 2.635,2.146 2.052,0.302 10 false No. 3 Junction Connector 1.698,1.333 2.156,1.531 0.458,0.198 10 false 20 1.729,0.75 2.188,0.948 0.458,0.198 10 false 9 5.323,0.729 5.781,0.927 0.458,0.198 10 false 5 5.323,1.323 5.781,1.521 0.458,0.198 10 false 4 5.625,0.875 6.083,1.073 0.458,0.198 10 false CANP 5.604,2.469 6.063,2.667 0.458,0.198 10 false IG2 5.625,1.458 6.083,1.656 0.458,0.198 10 false CANN 5.344,2.344 5.802,2.542 0.458,0.198 10 false 6 5.604,3.063 6.063,3.26 0.458,0.198 10 false GND 5.292,2.938 5.75,3.135 0.458,0.198 10 false 10 3.865,2.313 4.927,2.573 1.063,0.26 10 false A/BAG-IG2 1.625,2.469 3.104,2.75 1.479,0.281 10 false from IG2-NO. 2 Relay 5.313,4.083 5.729,4.354 0.417,0.271 10 false a6 5.51,4.083 7.104,4.49 1.594,0.406 10 false Occupant Detection ECU

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (OCCUPANT DETECTION ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the a6 occupant detection ECU connector.


c.
C351149C13
0.26,1.219 0.594,1.469 0.333,0.25 1.802,1.177 1.802,0.51 1.802,0.51 1.635,0.51 true 1.948,1.188 1.948,0.521 1.948,0.521 2.115,0.521 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.354,1.25 0.729,1.521 0.375,0.271 10 false a6 1.24,0.438 1.844,0.771 0.604,0.333 10 false CANN 2.208,0.448 2.813,0.781 0.604,0.333 10 false CANP
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a6-5 (CANP) - a6-4 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (OCCUPANT DETECTION ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C351149C14
0.26,1.219 0.594,1.469 0.333,0.25 1.354,1.427 1.354,1.99 1.354,1.99 1.188,1.99 true 1.948,1.427 1.948,1.99 1.948,1.99 2.115,1.99 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.354,1.25 0.667,1.448 0.313,0.198 10 false a6 0.938,1.917 1.365,2.073 0.427,0.156 10 false IG2 2.198,1.906 2.625,2.063 0.427,0.156 10 false GND
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a6-10 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a6-6 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)