Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2017.09–2018.04
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 3 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly

(w/ Radio and Display Type)

·

No. 4 CAN junction connector



WIRING DIAGRAM

C381547E01
0.385,1.01 1.156,1.208 0.771,0.198 10 false 120 Ω 0.385,5.667 1.156,5.865 0.771,0.198 10 false 120 Ω 0.906,0.667 1.677,0.865 0.771,0.198 10 false CA3H 0.948,1.156 1.719,1.354 0.771,0.198 10 false CA3L 1.427,0.667 2.198,0.865 0.771,0.198 10 false 6 1.427,1.146 2.198,1.344 0.771,0.198 10 false 21 2.781,0.781 3.552,0.979 0.771,0.198 10 false K127 2.781,1.26 3.552,1.458 0.771,0.198 10 false K127 2.854,1.042 3.625,1.24 0.771,0.198 10 false 20 2.896,0.552 3.667,0.75 0.771,0.198 10 false 9 2.781,5.896 3.552,6.094 0.771,0.198 10 false K127 2.781,5.427 3.552,5.625 0.771,0.198 10 false K127 4.052,2.99 4.823,3.188 0.771,0.198 10 false K128 4.063,3.469 4.833,3.667 0.771,0.198 10 false K128 4.177,2.781 4.948,2.979 0.771,0.198 10 false 1 4.135,3.26 4.906,3.458 0.771,0.198 10 false 12 5.104,3.896 5.542,4.177 0.438,0.281 10 false K2 5.833,2.875 6.229,3.104 0.396,0.229 10 false 13 5.833,3.354 6.229,3.583 0.396,0.229 10 false 14 6.073,2.99 6.583,3.25 0.51,0.26 10 false CANH 6.083,3.458 6.594,3.719 0.51,0.26 10 false CANL 5.385,3.896 7.094,4.479 1.708,0.583 10 false Radio and Display Receiver Assembly* 1.427,5.302 2.198,5.5 0.771,0.198 10 false 19 2.875,5.698 3.646,5.896 0.771,0.198 10 false 22 0.906,5.323 1.417,5.583 0.51,0.26 10 false CAYH 0.958,5.813 1.469,6.073 0.51,0.26 10 false CAYL 0.073,6.302 0.844,6.5 0.771,0.198 10 false K76 0.375,6.302 2.313,6.896 1.938,0.594 10 false Central Gateway ECU (Network Gateway ECU) 3,6.365 4.25,7.198 1.25,0.833 10 false No. 4 CAN Junction Connector 4.677,5.573 6.74,6.01 2.063,0.438 10 false *: w/ Radio and Display Type 2.865,5.167 3.635,5.365 0.771,0.198 10 false 11 1.427,5.802 2.198,6 0.771,0.198 10 false 20

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K127 No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372332C92
1.323,1.344 1.813,1.615 0.49,0.271 4.083,1.427 4.083,0.594 4.083,0.594 3.917,0.594 true 4.094,1.708 4.094,2.208 4.094,2.208 3.927,2.208 true 4.438,1.427 4.438,0.594 4.438,0.594 4.604,0.594 true 4.427,1.698 4.427,2.198 4.427,2.198 4.594,2.198 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,1.406 1.833,1.667 0.417,0.26 10 false K127 3.344,0.51 4.021,0.802 0.677,0.292 10 false CANH*b 3.365,2.125 4.042,2.417 0.677,0.292 10 false CANL*b 4.688,0.521 5.365,0.813 0.677,0.292 10 false CANH*b 4.656,2.115 5.333,2.406 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
K127-9 (CANH) - K127-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
K127-11 (CANH) - K127-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

NG

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the K128 No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C380534C14
0.854,1.323 1.333,1.583 0.479,0.26 2.75,1.427 2.75,0.75 2.75,0.75 2.583,0.75 true 2.771,1.688 2.771,2.104 2.771,2.104 2.604,2.104 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.948,1.375 1.344,1.583 0.396,0.208 10 false K128 2.042,0.688 2.604,0.938 0.563,0.25 10 false CANH*b 2.073,2.021 2.635,2.271 0.563,0.25 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Radio and Display Receiver Assembly
(w/ Radio and Display Type)


Standard Resistance:
Tester Connection Condition Specified Condition
K128-1 (CANH) - K128-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Result
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

4.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C372332C92
1.323,1.344 1.813,1.615 0.49,0.271 4.083,1.427 4.083,0.594 4.083,0.594 3.917,0.594 true 4.094,1.708 4.094,2.208 4.094,2.208 3.927,2.208 true 4.438,1.427 4.438,0.594 4.438,0.594 4.604,0.594 true 4.427,1.698 4.427,2.198 4.427,2.198 4.594,2.198 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,1.406 1.833,1.667 0.417,0.26 10 false K127 3.344,0.51 4.021,0.802 0.677,0.292 10 false CANH*b 3.365,2.125 4.042,2.417 0.677,0.292 10 false CANL*b 4.688,0.521 5.365,0.813 0.677,0.292 10 false CANH*b 4.656,2.115 5.333,2.406 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
K127-9 (CANH) - K127-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
K127-11 (CANH) - K127-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C365212C20
1.479,0.083 1.906,0.333 0.427,0.25 1.229,0.469 1.396,0.469 1.396,0.469 1.396,0.969 true 1.25,1.719 1.417,1.719 1.417,1.719 1.417,1.135 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.594,0.115 2.031,0.365 0.438,0.25 10 false K76 0.802,0.396 1.24,0.646 0.438,0.25 10 false CA3H 0.865,1.646 1.302,1.896 0.438,0.25 10 false CA3L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K76-6 (CA3H) - K76-21 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR