The motor generator control ECU, which is built into the inverter with converter assembly, controls the motor (MG2) based on commands from the hybrid vehicle control ECU assembly.
The motor generator control ECU (MG ECU) monitors communication data and detects malfunctions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P31241F | Lost Communication between Drive Motor "A" and HV ECU Circuit Intermittent | Error in reception from hybrid vehicle control ECU via serial communication (out of communication standard) detected when DTC P0C7917, P0D3319, P0E5717, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic) |
·
Wire harness or connector ·
Inverter with converter assembly ·
Hybrid vehicle control ECU assembly |
Does not come on | Master Warning Light:
Does not come on |
| P312487 | Lost Communication between Drive Motor "A" and HV ECU Missing Message | Error in reception from hybrid vehicle control ECU assembly via serial communication (out of communication standard)
(1 trip detection logic) |
·
Wire harness or connector ·
Inverter with converter assembly ·
Hybrid vehicle control ECU assembly |
Comes on | Master Warning Light:
Comes on |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 2 minutes or more.
Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Refer to the wiring diagram for the Inverter Low-voltage Circuit.
Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Motor Generator / Trouble Codes.
Clear the DTCs.
Turn the power switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Motor Generator / Utility / Diagnosis Related Information.
| Tester Display |
|---|
| Diagnosis Related Information |
Enter the following menus: Powertrain / Motor Generator / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P31241F or P312487 is listed in Diagnosis Related Information or DTC P31241F or P312487 is output. | A |
| P31241F and P312487 is not listed in Diagnosis Information and DTC P31241F and P312487 is not output. | B |
Turn the power switch off.
A
B
Connect an oscilloscope between the hybrid vehicle control ECU assembly terminals specified in the following table.
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
Measure the waveform.
| Item | Contents |
|---|---|
| Tester Connection | CH1: A29-31 (HMCH) - K69-6 (E1)
CH2: A29-30 (HMCL) - K69-6 (E1) |
| Equipment Setting | 1 V/DIV., 200 μs./DIV. |
| Condition | Power switch on (IG) |
| Result | Proceed to |
|---|---|
| The waveform appears as shown in the illustration. | A |
| The waveform differs from the one shown in the illustration. | B |
Perform this inspection with the connector connected.
If pulses are generated, the shape of the waveform can be assumed to be normal.
The shape of the waveform may vary according to communication conditions.
Turn the power switch off.
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the A48 inverter with converter assembly connector.
Disconnect the A29 hybrid vehicle control ECU assembly connector.
| *a | Front view of wire harness connector
(to Inverter with Converter Assembly) |
| *b | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-20 (HMCH) - A29-31 (HMCH) | Power switch off | Below 1 Ω |
| A48-19 (HMCL) - A29-30 (HMCL) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-20 (HMCH) or A29-31 (HMCH) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| A48-19 (HMCL) or A29-30 (HMCL) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
As there might be an intermittent malfunction, inspect the following items even if the measured resistance is as specified.
Check that each connector between the inverter with converter assembly and hybrid vehicle control ECU assembly is not loose or disconnected.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-20 (HMCH) or A29-31 (HMCH) - Body ground and other terminals | Power switch on (IG) | Below 1 V |
| A48-19 (HMCL) or A29-30 (HMCL) - Body ground and other terminals | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the hybrid vehicle control ECU assembly and inverter with converter assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Reconnect the A29 hybrid vehicle control ECU assembly connector.
Reconnect the A48 inverter with converter assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A29 hybrid vehicle control ECU assembly connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-31 (HMCH) - A29-30 (HMCL) | Power switch off | 80 to 170 Ω |
Reconnect the A29 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG