Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID VEHICLE CONTROL ECU › 2017.09–2019.02
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0328986 HYBRID VEHICLE CONTROL ECU A

HYBRID / BATTERY CONTROL  HYBRID VEHICLE CONTROL ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle control ECU assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of hybrid vehicle control ECU assembly Code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart entry and start system (for entry function)

·

Smart entry and start system (for start function)

·

Steering lock function


See Service Bulletin for the registration method.

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 73900 1.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

Hide 55308B 2.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)

Hide 64718C 3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for RHD)

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (for RHD)

Hide 67914 5.REMOVE FRONT DOOR SCUFF PLATE LH (for RHD)

Hide 62112A 6.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)

Hide 62312B 7.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)

Hide 55318C 8.REMOVE INSTRUMENT SIDE PANEL LH (for RHD)

Hide 55607 9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 55435B 10.REMOVE NO. 1 METER HOOD CLUSTER (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 55012A 11.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 55476C 12.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 55303B 13.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 89980 14.REMOVE HYBRID VEHICLE CONTROL ECU ASSEMBLY

a.
A413732C01
0.104,0.083 0.365,0.302 0.26,0.219 12 true *A 0.125,2.448 0.406,2.677 0.281,0.229 12 true *B
*A for LHD
*B for RHD


Disconnect the 4 hybrid vehicle control ECU assembly connectors.


b.

Remove the bolt, nut and hybrid vehicle control ECU assembly.