Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Oil Level Sensor Circuit  


DESCRIPTION

The combination meter assembly and engine oil level sensor are connected via direct line. The combination meter assembly determines the engine oil level based on the engine oil level sensor ON/OFF signal.

HINT:

As the engine oil level may be unstable when the engine is cold or running at high speeds, the combination meter assembly receives the engine coolant temperature signal and engine speed signal from the ECM via CAN communication in order to prevent the oil level warnings from being output erroneously.


WIRING DIAGRAM

E369059E01
2.302,1.448 2.76,1.646 0.458,0.198 10 false ECM 2.417,2.615 3.917,2.833 1.5,0.219 10 false Engine Oil Level Sensor 0.552,3.438 2.25,3.656 1.698,0.219 10 false : CAN Communication Line 4.594,3.104 6.438,3.344 1.844,0.24 10 false Combination Meter Assembly 4.604,2.948 4.885,3.135 0.281,0.188 10 false K21 4.667,2.146 4.948,2.333 0.281,0.188 10 false 27 3.5,2.167 3.656,2.354 0.156,0.188 10 false 1 4.938,2.156 5.333,2.333 0.396,0.177 10 false OILW 5.656,1.802 6.021,1.99 0.365,0.188 10 false 12 V 2.417,2.448 2.75,2.635 0.333,0.188 10 false C38

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

The following troubleshooting procedure is based on the assumption that the SFI system is normal. Confirm that the SFI system is not malfunctioning before performing the following procedure.

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.INSPECT ENGINE OIL LEVEL SENSOR
a.

Remove the engine oil level sensor.

Click hereEngine / Hybrid System>A25A-FXS (LUBRICATION)>OIL LEVEL SENSOR>REMOVAL


b.

Inspect the engine oil level sensor.

Click hereEngine / Hybrid System>A25A-FXS (LUBRICATION)>OIL LEVEL SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL LEVEL SENSOR - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL LEVEL SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the K21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C38-1 - K21-27 (OILW) Always Below 1 Ω
C38-1 or K21-27 (OILW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR