Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM33C0E _58 Vehicle Interior _065458 METER / GAUGE / DISPLAY _0330016 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Lid Opener System Operation Message Display Malfunction  


DESCRIPTION

The combination meter assembly and ECM are connected via direct line. The combination meter assembly displays fuel lid opener system operation messages according to the fuel lid signals received from the ECM.

WIRING DIAGRAM

E358411E03
4.385,2.323 6.198,2.698 1.813,0.375 10 false Combination Meter Assembly 4.396,2.188 4.708,2.385 0.313,0.198 10 false K21 1.927,2.188 2.385,2.385 0.458,0.198 10 false ECM 1.521,2.188 1.979,2.385 0.458,0.198 10 false A22 1.927,1.146 2.542,1.344 0.615,0.198 10 false LSTM 4.885,1.156 5.5,1.354 0.615,0.198 10 false LST1 2.417,1.042 2.729,1.24 0.313,0.198 10 false 41 4.563,1.042 4.875,1.24 0.313,0.198 10 false 34

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

The following troubleshooting procedure is based on the assumption that the SFI system and fuel lid opener system are normal. Confirm that the SFI system and fuel lid opener system are not malfunctioning before performing the following procedure.

SFI system (w/ Canister Pump Module): Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING

SFI system (w/o Canister Pump Module): Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING

Fuel lid opener system: Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
A402428C07
0.198,0.917 0.583,1.146 0.385,0.229 1.552,1.219 1.896,1.927 true 0.219,0.25 0.531,0.448 0.313,0.198 10 false *a 1.958,1.875 2.635,2.177 0.677,0.302 10 false LSTM 0.271,0.958 0.583,1.156 0.313,0.198 10 false A22
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the A22 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-41 (LSTM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
2.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
E284677C60
1.5,0.208 1.906,0.458 0.406,0.25 0.854,1.719 1.354,1.125 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.583,0.25 1.885,0.479 0.302,0.229 10 false K21 0.729,1.75 1.146,1.969 0.417,0.219 10 false LST1
*a Component with harness connected
(Combination Meter Assembly)


a.

Check the input waveform.

i.

Connect the A22 ECM connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal K21-34 (LST1) and body ground.


iv.

Operate the fuel lid opener switch.


v.

Check the signal waveform according to the condition(s) in the table below.

A375178E03
2.76,0.927 3.333,1.125 0.573,0.198 10 false GND

Waveform 1:

Item Condition
Tester Connection K21-34 (LST1) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition "Ready to Refuel" displayed on multi-information display

A375177E03
2.771,0.938 3.323,1.146 0.552,0.208 10 false GND

Waveform 2:

Item Condition
Tester Connection K21-34 (LST1) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition "Close Fuel Lid" displayed on multi-information display

HINT:

This waveform is output when the fuel lid opener switch is operated if the fuel lid is open and any of the following conditions are met:

·

The vehicle has been driven for 1 km (0.6 mile) or more at a speed of 50 km/h (31 mph) or more.

·

30 minutes or more have elapsed since the fuel lid opener switch was operated.




OK:

All of the waveforms are output normally.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
a.

Disconnect the K21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-41 (LSTM) - K21-34 (LST1) Always Below 1 Ω
A22-41 (LSTM) or K21-34 (LST1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR