Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2017.09–2020.08
RM33C0E _58 Vehicle Interior _065464 HEATING / AIR CONDITIONING _0329891 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1473  A/C Inverter Start-up Signal System Malfunction  


DESCRIPTION

The inverter activation signal is sent to the compressor with motor assembly from the hybrid vehicle control ECU assembly. Compressor control is stopped and this DTC is stored if there is an open or short in the signal circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1473 A/C Inverter Start-up Signal System Malfunction Open or short in A/C inverter start-up signal circuit
·

Compressor with motor assembly

·

Hybrid vehicle control ECU assembly

·

Hybrid control system

·

Air conditioning amplifier assembly


-

WIRING DIAGRAM

E334616E12
0.927,1.813 1.385,2.01 0.458,0.198 10 false LIN 1.396,4.146 1.854,4.344 0.458,0.198 10 false 2 0.073,0.958 2.521,1.188 2.448,0.229 10 false Air Conditioning Amplifier Assembly 0.781,3.219 1.24,3.417 0.458,0.198 10 false DOUT 0.938,3.771 1.396,3.969 0.458,0.198 10 false IG1 0.865,4.344 1.323,4.542 0.458,0.198 10 false GND 0.958,5.104 1.417,5.302 0.458,0.198 10 false PB 0.958,5.625 1.417,5.823 0.458,0.198 10 false PE 1.375,5.104 1.813,5.281 0.438,0.177 10 false t1 1.302,4.344 1.74,4.521 0.438,0.177 10 false C70 1.302,3.771 1.74,3.948 0.438,0.177 10 false C70 1.302,3.219 1.74,3.396 0.438,0.177 10 false C70 1.25,1.646 1.708,1.844 0.458,0.198 10 false 1 1.385,3.583 1.844,3.781 0.458,0.198 10 false 1 1.385,3.021 1.844,3.219 0.458,0.198 10 false 3 1.385,4.917 1.844,5.115 0.458,0.198 10 false 2 1.385,5.448 1.854,5.646 0.469,0.198 10 false 1 0.094,2.313 0.552,2.51 0.458,0.198 10 false W11 0.104,2.469 2.552,2.698 2.448,0.229 10 false Battery State Sensor Assembly 2.198,3.917 3.271,4.198 1.073,0.281 10 false ECU-IG1 NO. 3 2.604,6.177 4.208,6.417 1.604,0.24 10 false Air Conditioning Wire 0.281,6.417 1.333,6.896 1.052,0.479 10 false Compressor with Motor Assembly 2.219,7.01 4.698,7.344 2.479,0.333 10 false : CAN Communication Line 2.219,7.417 4.156,7.698 1.938,0.281 10 false : LIN Communication Line 4.969,6.854 7.031,7.177 2.063,0.323 10 false Inverter with Converter Assembly 4.969,6.677 5.406,6.854 0.438,0.177 10 false t2 5.438,3.833 7.146,4.198 1.708,0.365 10 false Hybrid Vehicle Control ECU Assembly 5.438,3.656 5.875,3.833 0.438,0.177 10 false A28 5.083,5 5.542,5.198 0.458,0.198 10 false 1 5.083,5.521 5.542,5.719 0.458,0.198 10 false 2 5.281,5 5.719,5.177 0.438,0.177 10 false ACPB 5.281,5.521 5.719,5.698 0.438,0.177 10 false ACPE 6.031,3.219 6.469,3.396 0.438,0.177 10 false LIN3 5.792,3.042 6.25,3.24 0.458,0.198 10 false 17 3.76,3.771 5.75,3.969 1.99,0.198 10 false from IG1-NO. 1 Relay 1.375,5.625 1.813,5.802 0.438,0.177 10 false t1

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.

·

The air conditioning system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Check if air conditioning system DTCs are output.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
Only B1473 is output A
B1473 and B1498 are output simultaneously B



A

2.CHECK FOR DTC

B

2.CHECK FOR DTC
a.

Check if hybrid control system DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 236

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.PERFORM ACTIVE TEST USING GTS

B

3.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Compressor Target Speed Compressor with motor assembly Min.: 0
Max.: 7500
-
Body Electrical > Air Conditioner > Active Test
Tester Display
Compressor Target Speed
50004 121 18
OK:

Compressor with motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY