Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065464 HEATING / AIR CONDITIONING _0329891 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1475  A/C Inverter Cooling / Heating System Malfunction  


DESCRIPTION

The temperature sensor of the compressor with motor assembly detects the A/C inverter temperature.

If the temperature exceeds the maximum, operation of the compressor with motor assembly will be stopped, and this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1475 A/C Inverter Cooling / Heating System Malfunction A/C inverter temperature outside specified range (temperature too high) or open or short to ground in temperature sensor circuit
·

Cooling fan system

·

Refrigerant volume

·

Compressor with motor assembly


Memorized

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.

·

The air conditioning system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Engine Cooling Fan Duty Ratio Control the cooling fan 0 to 100% Perform this test when vehicle is stopped.
Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11
OK:

Cooling fan operates smoothly.



Result:
Proceed to
OK
NG



OK

2.CHECK REFRIGERANT PRESSURE

NG

2.CHECK REFRIGERANT PRESSURE

b.

Turn the power switch on (READY).


c.

Read the manifold gauge pressure when the following conditions are met.

i.

Prepare the vehicle according to the table below.

Item Condition
Vehicle doors Fully open
Temperature setting MAX COLD
Blower speed HI
A/C switch On
Recirculation/fresh switch RECIRCULATION
Interior temperature 25 to 35°C (77 to 95°F)



Standard Pressure:
Low pressure side:

150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)

High pressure side:

1370 to 1570 kPa (14 to 16 kgf/cm2, 199 to 228 psi)


Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

3.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

Result:
Proceed to
NEXT



NEXT

4.READ OUTPUT DTC (DTC B1475)
4.READ OUTPUT DTC (DTC B1475)
a.

Turn the power switch on (READY).


b.

Prepare the vehicle according to the table below.

Item Condition
Blower speed HI
A/C switch On
Temperature setting MAX COLD


c.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
B1475 is not output A
B1475 is output B


NOTICE:

If the engine idles continuously when ambient temperature is high, the compressor with motor assembly may automatically stop to protect the inverter circuit, and DTC B1475 may be stored.



A

B

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY