The No. 4 air conditioning radiator damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air outlet damper to the appropriate position, which controls the air outlet switching.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
The No. 1 air conditioning radiator damper servo sub-assembly (mode) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air outlet damper to the appropriate position, which controls the air outlet switching.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
The No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air outlet damper to the appropriate position, which controls the air outlet switching.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1443 | Air Outlet Damper Control Servo Motor Circuit | for LHD (for 3 Zone Type):
Air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 4 air conditioning radiator damper servo sub-assembly for LHD (except 3 Zone Type):
Air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (mode) for RHD:
Air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) |
·
No. 4 air conditioning radiator damper servo sub-assembly*2 ·
No. 1 air conditioning radiator damper servo sub-assembly (mode)*3 ·
No. 1 air conditioning radiator damper servo sub-assembly (driver side mode)*4 ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly ·
Air conditioning radiator assembly |
Memorized
(30 sec. or more)*1 |
*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
*2: for LHD (for 3 Zone Type)
*3: for LHD (except 3 Zone Type)
*4: for RHD
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition*1 | No. 4 air conditioning radiator damper servo sub-assembly operating | ○ | ○ |
| Diagnosis Condition*2 | No. 1 air conditioning radiator damper servo sub-assembly (mode) operating | ○ | ○ |
| Diagnosis Condition*3 | No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) operating | ○ | ○ |
| Malfunction | Air outlet damper servo operation request signals are output but the air outlet damper position sensor value does not change | ○ | - |
| Air outlet damper servo operation request signals are output but the air outlet damper position sensor value is abnormal | - | ○ | |
| Detection Time | Continuously for 30 seconds or more | Continuously for 30 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
*1: for LHD (for 3 Zone Type)
*2: for LHD (except 3 Zone Type)
*3: for RHD
If the conditions of either of these patterns are detected, a DTC will be stored
for LHD (for 3 Zone Type)
for LHD (except 3 Zone Type)
for RHD
Confirm that no mechanical problems are present because this DTC can be stored when either a damper link or damper is mechanically locked.
When installing a damper servo motor, make sure to install it correctly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REASSEMBLY
After replacing a damper servo motor, make sure to perform Servo Motor Initialization.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LHD (for 3 Zone Type) | A |
| for LHD (except 3 Zone Type) | B |
| for RHD | C |
A
B
C
Check for DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Check that the No. 4 air conditioning radiator damper servo sub-assembly is installed correctly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REASSEMBLY
The No. 4 air conditioning radiator damper servo sub-assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 4 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Operate the dampers by hand.
The dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Connect the No. 2 air conditioning radiator damper servo sub-assembly connector to the No. 4 air conditioning radiator damper servo sub-assembly.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| A/O Servo Pulse(Rr D) | No. 2 air conditioning radiator damper servo sub-assembly pulse* | Min.: 128
Max.: 383 |
Operates between 158 to 260 pulses |
*: Thus this Active Test is for the No. 2 air conditioning radiator damper servo sub-assembly, in this case it is used to check the operation of the No. 4 air conditioning radiator damper servo sub-assembly.
| Tester Display |
|---|
| A/O Servo Pulse(Rr D) |
The No. 4 air conditioning radiator damper servo sub-assembly operates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B1497 is output | A |
| B1441, B1442, B1443 and B1446 are output | B |
| Only B1443 is output | C |
A
B
C
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only B1497 is output | A |
| B1441, B1442, B1443 and B1446 are output | B |
| Only B1443 is output | C |
A
B
C
Check that the No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REASSEMBLY
The No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Operate the dampers by hand.
The dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
OK
NG