Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0330906 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction is detected in the starter circuit inside the certification ECU (smart key ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2275 STSW Monitor Malfunction Certification ECU (smart key ECU assembly) internal HV activation request output circuit malfunction or external circuit malfunction (1-trip detection logic*)
·

Certification ECU (smart key ECU assembly)

·

Hybrid vehicle control ECU assembly

·

Wire harness or connector


DTC Output Confirmation Operation:

Turn the power switch on (IG) and wait 10 seconds or more, then start the hybrid control system 3 times.



*: Only detected while a malfunction is present and the power switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

The power source mode changes to on (READY) even though the hybrid control system is not started.

·

The power source mode does not change to on (READY) even though the hybrid control system is started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2275
Power Source Control
·

Starter Request Signal



WIRING DIAGRAM

B481557E04
1.271,0.708 1.927,0.958 0.656,0.25 10 false ST2 0.521,1.885 1.177,2.135 0.656,0.25 10 false K69 0.521,2.031 1.896,2.5 1.375,0.469 10 false Hybrid Vehicle Control ECU Assembly 5.083,1.896 5.74,2.146 0.656,0.25 10 false K62 5.083,2.052 6.615,2.469 1.531,0.417 10 false Certification ECU (Smart Key ECU Assembly) 1.635,0.708 2.292,0.958 0.656,0.25 10 false 9 5.01,0.708 5.667,0.958 0.656,0.25 10 false 27 5.271,0.708 5.927,0.958 0.656,0.25 10 false ST2 5.719,0.333 6.375,0.583 0.656,0.25 10 false +B 6.208,0.917 6.865,1.167 0.656,0.25 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the hybrid vehicle control ECU assembly or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Turn the power switch on (IG) and wait 25 seconds.


b.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

DTC B2285 is not output simultaneously.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K69 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-27 (ST2) - K69-9 (ST2) Always Below 1 Ω
K62-27 (ST2) or K69-9 (ST2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the K69 hybrid vehicle control ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K62-27 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1 V or less



Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)