Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0330906 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG drive circuit or IG hold circuit of the certification ECU (smart key ECU assembly) or a malfunction in the IG output circuit between the output terminal of the certification ECU (smart key ECU assembly) and IG relay is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2271 Ignition Hold Monitor Malfunction When either of the following conditions is met (1-trip detection logic*1):
·

The IG circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*2

·

The IG hold circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*3

·

There is a malfunction in a circuit outside of the certification ECU (smart key ECU assembly) circuit.


·

Certification ECU (smart key ECU assembly)

·

Instrument panel junction block assembly

·

Wire harness or connector


DTC Output Confirmation Operation:

Turn the power switch on (IG).



*1: Only detected while a malfunction is present and the power switch is on (IG).

*2: The IG circuit and IG hold circuit activate the IG relay.

*3: After the IG circuit turns on, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit will maintain the power source mode in on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power switch cannot be turned on (IG) (the hybrid control system cannot be started). The power source mode cannot be changed to on (IG).

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2271
Power Source Control
·

IG Relay Monitor (Inside)

·

Latch Circuit



WIRING DIAGRAM

B630383E81
0.365,2.073 2.167,2.667 1.802,0.594 10 false Engine Room Relay Block and Junction Block Assembly 6.188,0.365 7.042,0.75 0.854,0.385 10 false from Auxiliary Battery 5.615,4.448 7.156,4.906 1.542,0.458 10 false Certification ECU (Smart key ECU assembly) 0.75,1.094 0.906,1.292 0.156,0.198 10 false 2 1.635,1.094 1.792,1.292 0.156,0.198 10 false 1 0.948,1.833 1.552,2.052 0.604,0.219 10 false IG2 NO.1 3.615,3.063 4.219,3.281 0.604,0.219 10 false IG2-NO.2 3.646,5.031 4.25,5.25 0.604,0.219 10 false IG1-NO.2 3.604,6.917 4.208,7.135 0.604,0.219 10 false IG1-NO.1 2.469,1.156 2.781,1.354 0.313,0.198 10 false 3C 2.479,0.938 2.729,1.146 0.25,0.208 10 false 13 2.458,6.25 2.771,6.448 0.313,0.198 10 false 3B 2.5,6.052 2.75,6.26 0.25,0.208 10 false 3 5.063,2.375 5.375,2.573 0.313,0.198 10 false 3A 5.083,2.177 5.333,2.385 0.25,0.208 10 false 17 5.833,2.292 6.208,2.49 0.375,0.198 10 false IG1D 5.563,2.292 5.813,2.5 0.25,0.208 10 false 17 5.615,4.292 5.896,4.49 0.281,0.198 10 false K62 6.177,1.885 6.49,2.083 0.313,0.198 10 false +B 6.698,2.219 6.844,2.427 0.146,0.208 10 false IC 5.615,1.292 5.865,1.5 0.25,0.208 10 false 4 5.823,1.385 6.135,1.583 0.313,0.198 10 false +B 5.438,0.531 5.75,0.729 0.313,0.198 10 false AM2 3.073,7.469 4.708,8.167 1.635,0.698 10 false Instrument Panel Junction Block Assembly 5.573,3.719 5.823,3.927 0.25,0.208 10 false 18 5.844,3.823 6.156,4.021 0.313,0.198 10 false E 1.646,1.385 1.896,1.594 0.25,0.208 10 false 3 0.75,1.385 1,1.594 0.25,0.208 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B574617C15
1.542,2.073 1.948,2.344 0.406,0.271 1.792,4.073 1.583,4.073 1.583,4.073 1,3.333 true 0.448,2.906 0.76,3.104 0.313,0.198 10 false *a 1.635,2.115 1.948,2.313 0.313,0.198 10 false E52 1.885,3.99 2.198,4.188 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the E52 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E52-6 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B574617C16
1.573,2.104 1.969,2.323 0.396,0.219 1.885,4.042 2.021,4.042 2.021,4.042 2.25,3.49 true 0.406,2.719 0.719,2.917 0.313,0.198 10 false *a 1.74,3.969 1.896,4.167 0.156,0.198 10 false E 1.646,2.135 1.917,2.375 0.271,0.24 10 false E52
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52-29 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the A15 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 4B and 4C power distribution box assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A15-24 (IGPD) - 4C-17 Always Below 1 Ω
A15-11 (IGRD) - 4B-11 Always Below 1 Ω
A15-24 (IGPD) or 4C-17 - Other terminals and body ground Always 10 kΩ or higher
A15-11 (IGRD) or 4B-11 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Disconnect the 4D power distribution box assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4C-17 - 4D-13 Always Below 1 Ω
4C-17 or 4D-13 - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - IGP RELAY)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - IGP RELAY)
a.

Remove the IGP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-13 - No. 1 engine room relay block and No. 1 junction block assembly IGP relay terminal 1 Always Below 1 Ω
4D-13 or No. 1 engine room relay block and No. 1 junction block assembly IGP relay terminal 1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT IGP RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT IGP RELAY

OK

7.CHECK POWER DISTRIBUTION BOX ASSEMBLY

NG

REPLACE IGP RELAY

7.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-11 - 4B-36 Always 135 to 165 Ω
4B-11 - 4C-41 Always 135 to 165 Ω
4B-11 or 4B-36 - Other terminals Always 10 kΩ or higher
4B-11 or 4C-41 - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY