Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0330906 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser function compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the hybrid vehicle control ECU assembly or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.



HINT:

If an immobiliser function or hybrid control system DTC is output, first perform troubleshooting for the immobiliser function or hybrid control system DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS

B

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts within 5 seconds of the power switch being turned on (READY).

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI AND IMO)
3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI AND IMO)
a.

Using an oscilloscope, check the waveform.

B384271C14
5.385,0.104 5.76,0.333 0.375,0.229 5.292,2.323 5.51,2.323 5.51,2.323 5.51,1.073 true 5.854,2.323 5.625,2.323 5.625,2.323 5.625,1.083 true 3.406,4.198 3.177,4.198 3.177,4.198 3.177,3.646 false 2.771,4.198 2.99,4.198 2.99,4.198 2.99,3.646 false 3.823,6.135 3.594,6.135 3.594,6.135 3.594,5.688 false 3.625,6.302 3.396,6.302 3.396,6.302 3.396,5.698 false 0.625,0.24 0.906,0.448 0.281,0.208 10 false *a 2.604,4.104 2.917,4.26 0.313,0.156 10 false *b 3.458,4.115 3.771,4.271 0.313,0.156 10 false *c 1.854,7.125 2.167,7.281 0.313,0.156 10 false *d 1.938,7.365 2.25,7.521 0.313,0.156 10 false *e 2.458,4.635 2.771,4.792 0.313,0.156 10 false *f 3.042,2.677 3.344,3.01 0.302,0.333 10 false *g 3.469,4.635 3.781,4.792 0.313,0.156 10 false *h 1.448,6.5 1.76,6.656 0.313,0.156 10 false *i 5.458,0.135 5.896,0.385 0.438,0.25 10 false K70 5.01,2.24 5.448,2.49 0.438,0.25 10 false IMO 5.917,2.24 6.354,2.49 0.438,0.25 10 false IMI 1.042,3.615 1.552,3.906 0.51,0.292 10 false GND 1.052,5.656 1.563,5.948 0.51,0.292 10 false GND 3.865,6.073 4.177,6.229 0.313,0.156 10 false *c 3.667,6.24 3.979,6.396 0.313,0.156 10 false *b 3.177,6.5 3.49,6.656 0.313,0.156 10 false *i 3.74,7.125 4.052,7.281 0.313,0.156 10 false *d 3.677,7.365 3.99,7.521 0.313,0.156 10 false *e
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f Waveform 1
*g Waveform 2 *h Waveform 3
*i Waveform 1 (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:
Tester Connection Condition Tool Setting Specified Condition
K70-23 (IMO) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
K70-22 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1 and 3)



Result:
Result Proceed to
Normal waveform A
Waveform 1 is not output, or has abnormal wavelength or shape B
Waveform 2 is not output, or has abnormal wavelength or shape C
Waveform 3 is not output, or has abnormal wavelength or shape D



A

4.REGISTER ECU COMMUNICATION ID

B

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

C

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

D

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K70 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-3 (EFII) - K70-23 (IMO) Always Below 1 Ω
A13-3 (EFII) or K70-23 (IMO) - Other terminals and body ground Always 10 kΩ or higher
A13-4 (EFIO) - K70-22 (IMI) Always Below 1 Ω
A13-4 (EFIO) or K70-22 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


Result:
Proceed to
NEXT



NEXT

8.REGISTER RECOGNITION CODE
8.REGISTER RECOGNITION CODE
a.

Register the recognition codes to the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG