Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2017.09–2019.10
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  B242E  Open in IG Circuit  


DESCRIPTION

The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.

The IG terminal power source voltage is supplied by turning the IG1-NO. 1 relay to ON.

The headlight ECU sub-assembly receives power switch on (IG) signals from the main body ECU (multiplex network body ECU) via CAN communication, compares the power switch on (IG) signal and the power source voltage supply condition of the IG terminal and monitors the result.

HL AutoLeveling
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B242E Open in IG Circuit
Detection condition:

The power switch is on (IG).


Malfunction status:

When the IG terminal power source voltage is 0 V (power switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly LH

·

Harness or connector


Headlight ECU sub-assembly LH

HL AutoLeveling (Sub)
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B242E Open in IG Circuit
Detection condition:

The power switch is on (IG).


Malfunction status:

When the IG terminal power source voltage is 0 V (power switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly RH

·

Harness or connector


Headlight ECU sub-assembly RH

WIRING DIAGRAM

E370857E02
0.292,0.708 2.281,0.906 1.99,0.198 10 false from IG1-NO. 1 Relay 2.458,0.875 3.521,1.156 1.063,0.281 10 false ECU-IG1 NO. 3 4.708,1.885 5.146,2.125 0.438,0.24 10 false A10 4.719,4.115 5.125,4.354 0.406,0.24 10 false A11 4.708,2.031 7.021,2.313 2.313,0.281 10 false Headlight ECU Sub-assembly LH 4.708,4.25 7.125,4.5 2.417,0.25 10 false Headlight ECU Sub-assembly RH 5.021,0.625 5.229,0.875 0.208,0.25 10 false 4 5.01,2.844 5.219,3.094 0.208,0.25 10 false 4 5.188,0.729 5.427,0.948 0.24,0.219 10 false IG 5.188,2.948 5.427,3.167 0.24,0.219 10 false IG 4.948,1.25 5.156,1.5 0.208,0.25 10 false 12 4.938,3.469 5.146,3.719 0.208,0.25 10 false 12 5.177,1.354 5.552,1.615 0.375,0.26 10 false GND 5.177,3.563 5.552,3.823 0.375,0.26 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION



PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
OK:

DTC B242E is not output.



Result:
Result Proceed to
OK A
NG (DTC output from headlight ECU sub-assembly LH) B
NG (DTC output from headlight ECU sub-assembly RH) C



A

B

3.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH (IG TERMINAL VOLTAGE)

C

5.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH (IG TERMINAL VOLTAGE)
3.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH (IG TERMINAL VOLTAGE)
E355660C41
1.5,0.531 1.896,0.833 0.396,0.302 1.688,2.5 1.823,1.865 false 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 1.573,0.604 1.885,0.802 0.313,0.198 10 false A10 1.604,2.531 1.917,2.729 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


a.

Disconnect the A10 headlight ECU sub-assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A10-4 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A10-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH (IG TERMINAL VOLTAGE)
E355660C42
1.5,0.531 1.896,0.833 0.396,0.302 1.688,2.5 1.823,1.865 false 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 1.573,0.604 1.885,0.802 0.313,0.198 10 false A11 1.604,2.531 1.917,2.729 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)


a.

Disconnect the A11 headlight ECU sub-assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A11-4 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A11-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR