Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2017.09–2019.10
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0331112 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  B242F  Open in B Power Line  


DESCRIPTION

The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.

The power source voltage of the ECUB terminal is supplied when the main body ECU (multiplex network body ECU) turns the ECUB power supply relay (H-LP LH relay and H-LP RH relay) to ON.

The headlight ECU sub-assembly compares the power source voltage supply condition of the IG terminal and ECUB terminal and monitors the result.

HL AutoLeveling
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B242F Open in B Power Line
Detection condition:

The power switch is on (IG).


Malfunction status:

No power source voltage supplied to ECUB terminal while power source voltage being supplied to IG terminal


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly LH

·

Harness or connector

·

H-LP LH relay

·

Instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU)


Headlight ECU sub-assembly LH

HL AutoLeveling (Sub)
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B242F Open in B Power Line
Detection condition:

The power switch is on (IG).


Malfunction status:

No power source voltage supplied to ECUB terminal while power source voltage being supplied to IG terminal


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly RH

·

Harness or connector

·

H-LP RH relay

·

Main body ECU (multiplex network body ECU)


Headlight ECU sub-assembly RH

WIRING DIAGRAM

E370858E05
0.74,0.375 2.406,0.615 1.667,0.24 10 false from Auxiliary Battery 0.729,1.76 2.354,2.063 1.625,0.302 10 false from Auxiliary Battery 0.625,1.01 1.854,1.208 1.229,0.198 10 false H-LP LH 0.625,2.406 1.854,2.604 1.229,0.198 10 false H-LP RH 1.917,1.396 3.146,1.594 1.229,0.198 10 false H-LP LH 1.917,2.781 3.146,2.979 1.229,0.198 10 false H-LP RH 4.458,1.625 6.083,2.177 1.625,0.552 10 false Instrument Panel Junction Block Assembly 5.448,3.76 7.125,4.344 1.677,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 5.802,2.5 6.188,2.729 0.385,0.229 10 false K52 5.833,1.104 6.219,1.333 0.385,0.229 10 false MB 5.854,0.906 6.24,1.135 0.385,0.229 10 false 15 5.844,2.302 6.229,2.531 0.385,0.229 10 false 12 4.24,0.906 4.625,1.135 0.385,0.229 10 false 31 4.229,1.104 4.615,1.333 0.385,0.229 10 false 3C 6.177,1 6.646,1.24 0.469,0.24 10 false HRLY 6.177,2.385 6.646,2.635 0.469,0.25 10 false HRY2 2.292,3.948 2.75,4.167 0.458,0.219 10 false ECUB 2.292,5.927 2.75,6.146 0.458,0.219 10 false ECUB 2.75,3.854 3.208,4.073 0.458,0.219 10 false 13 2.74,5.802 3.198,6.021 0.458,0.219 10 false 13 1.833,2.146 2.01,2.354 0.177,0.208 10 false 5 1.823,0.75 2,0.958 0.177,0.208 10 false 5 1.813,1.031 1.99,1.24 0.177,0.208 10 false 2 1.823,2.406 2,2.615 0.177,0.208 10 false 2 2.469,0.75 2.646,0.958 0.177,0.208 10 false 3 2.469,1.031 2.646,1.24 0.177,0.208 10 false 1 2.458,2.406 2.635,2.615 0.177,0.208 10 false 1 2.458,2.156 2.635,2.365 0.177,0.208 10 false 3 1.583,4.49 1.969,4.719 0.385,0.229 10 false A10 1.583,6.458 1.969,6.688 0.385,0.229 10 false A11 1.594,4.656 2.865,5.198 1.271,0.542 10 false Headlight ECU Sub-assembly LH 1.573,6.615 2.833,7.292 1.26,0.677 10 false Headlight ECU Sub-assembly RH 1.469,3.865 1.927,4.083 0.458,0.219 10 false 12 1.677,3.948 2.135,4.167 0.458,0.219 10 false GND 1.677,5.927 2.135,6.146 0.458,0.219 10 false GND 1.479,5.823 1.938,6.042 0.458,0.219 10 false 12

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>INITIALIZATION



PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
OK:

DTC B242F is not output.



Result:
Result Proceed to
OK A
NG (DTC output from headlight ECU sub-assembly LH) B
NG (DTC output from headlight ECU sub-assembly RH) C



A

B

3.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH (ECUB TERMINAL VOLTAGE)

C

10.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH (ECUB TERMINAL VOLTAGE)
3.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH (ECUB TERMINAL VOLTAGE)
E355660C43
1.5,0.531 1.896,0.833 0.396,0.302 1.385,2.5 1.208,1.938 false 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 1.573,0.604 1.885,0.802 0.313,0.198 10 false A10 1.281,2.531 1.823,2.813 0.542,0.281 10 false ECUB
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


a.

Disconnect the A10 headlight ECU sub-assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A10-13 (ECUB) - Body ground Power switch on (IG) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)

NG

5.INSPECT H-LP LH RELAY
4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A10-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT H-LP LH RELAY
a.

Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT ECU SUB-ASSEMBLY LH)

NG

REPLACE H-LP LH RELAY

6.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP LH relay) - A10-13 (ECUB) Always Below 1 Ω
3 (H-LP LH relay) or A10-13 (ECUB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (H-LP LH relay) - Body ground Power switch off 11 to 14 V
5 (H-LP LH relay) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP LH relay) - 3C-31 Always Below 1 Ω
1 (H-LP LH relay) or 3C-31 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E367360C01
1.74,0.583 2.115,0.833 0.375,0.25 4.875,0.938 5.25,1.188 0.375,0.25 4.563,2.052 4.938,1.542 false 0.479,0.438 0.792,0.635 0.313,0.198 10 false *a 1.844,0.635 2.156,0.833 0.313,0.198 10 false 3C 4.948,0.979 5.26,1.177 0.313,0.198 10 false MB 4.396,2.083 4.927,2.313 0.531,0.229 10 false HRLY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-31 - MB-15 (HRLY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

10.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH (ECUB TERMINAL VOLTAGE)
E355660C44
1.5,0.531 1.896,0.833 0.396,0.302 1.385,2.5 1.208,1.938 false 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 1.573,0.604 1.885,0.802 0.313,0.198 10 false A11 1.281,2.531 1.823,2.813 0.542,0.281 10 false ECUB
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)


a.

Disconnect the A11 headlight ECU sub-assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A11-13 (ECUB) - Body ground Power switch on (IG) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)

NG

12.INSPECT H-LP RH RELAY
11.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A11-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT H-LP RH RELAY
a.

Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT ECU SUB-ASSEMBLY RH)

NG

REPLACE H-LP RH RELAY

13.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP RH relay) - A11-13 (ECUB) Always Below 1 Ω
3 (H-LP RH relay) or A11-13 (ECUB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (H-LP RH relay) - Body ground Power switch off 11 to 14 V
5 (H-LP RH relay) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP RH relay) - K52-12 (HRY2) Always Below 1 Ω
1 (H-LP RH relay) or K52-12 (HRY2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR