Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › 2017.09–2018.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P062F46  Hybrid/EV Powertrain Control Module EEPROM Calibration / Parameter Memory Failure  


DESCRIPTION

The hybrid vehicle control ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P062F46 Hybrid/EV Powertrain Control Module EEPROM Calibration / Parameter Memory Failure Either of the following conditions is met:
·

ECU internal malfunction

(EEPROM error)

·

The power switch is turned off when the auxiliary battery voltage is 9.5 V or less.


(1 trip detection logic)
·

Hybrid vehicle control ECU Assembly

·

Auxiliary battery


Comes on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 15 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.READ VALUE USING GTS (VEHICLE CONTROL HISTORY (HYBRID CONTROL))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History.

Powertrain > Hybrid Control > Utility
Tester Display
Vehicle Control History
50005 397 1055

d.

Read and record the vehicle control history (Hybrid Control).

Result:
Result Proceed to
Auxiliary Battery Voltage Low (HV) or Auxiliary Battery Voltage Low (Inverter) is stored. A
Auxiliary Battery Voltage Low (HV) and Auxiliary Battery Voltage Low (Inverter) are not stored. B



e.

Turn the power switch off.



A

2.READ VALUE USING GTS (FREEZE FRAME DATA (HYBRID CONTROL) AND VEHICLE CONTROL HISTORY (HYBRID CONTROL))

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

2.READ VALUE USING GTS (FREEZE FRAME DATA (HYBRID CONTROL) AND VEHICLE CONTROL HISTORY (HYBRID CONTROL))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Read the Freeze Frame Data of DTC P062F46.

HINT:

The value of the Freeze Frame Data item BATT Voltage immediately after the power switch is turned on (IG) may be 16.00 V (15.99 V), however this does not indicate a malfunction.


i.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

ii.

According to the display on the GTS, read the data of the Freeze Frame Data and make a note of the value of Total Distance Traveled.



d.

Read the data recorded in the Vehicle Control History item (Auxiliary Battery Voltage Low (HV) or Auxiliary Battery Voltage Low (Inverter)) which was stored when the auxiliary battery voltage dropped below the threshold.

i.

Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History.

Powertrain > Hybrid Control > Utility
Tester Display
Vehicle Control History
50005 397 1055

ii.

According to the display on the GTS, read the Vehicle Control History data and make a note of the value of Total Distance Traveled.



e.

Compare the values in the Freeze Frame Data and the Vehicle Control History.

Result:
Result Proceed to
The total distance driven is the same. A
The total distance driven is not the same. B



f.

Turn the power switch off.



A

3.CHECK AUXILIARY BATTERY VOLTAGE

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

3.CHECK AUXILIARY BATTERY VOLTAGE
a.

Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


b.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 20°C (68°F), Power switch off 11.0 V or higher


HINT:

This DTC may be stored when the power switch is turned off when the auxiliary battery voltage is low. In this case, when the auxiliary battery voltage is no longer low, after the power switch is turned on (IG) and then off several times, the vehicle will be judged as normal and the master warning light will turn off.


Result:
Proceed to
OK
NG




OK

5.CLEAR DTC

NG

4.RECHARGE OR REPLACE AUXILIARY BATTERY
4.RECHARGE OR REPLACE AUXILIARY BATTERY
Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
6.SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and turn the GTS on.


c.

With power switch on (IG) and wait for 15 seconds or more.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P062F46 is not output. A
P062F46 is output. B



f.

Turn the power switch off.



A

END

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY