Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P0A3611  Generator Temperature Sensor Circuit Short to Ground  P0A3615  Generator Temperature Sensor Circuit Short to Auxiliary Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the generator temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU assembly malfunction

Hybrid vehicle control ECU assembly internal malfunction


Generator temperature sensor malfunction
·

Internal generator temperature sensor malfunction

·

Open or short in generator temperature sensor


Wire harness between the generator temperature sensor and hybrid vehicle control ECU assembly
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness


HINT:

If any of these DTCs are stored, the generator temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the generator (MG1) becomes high. If the self-protection function does not operate, the generator (MG1) may malfunction and cause the vehicle to enter fail-safe mode.



DESCRIPTION

C189867E17
0.76,2.104 0.885,2.302 0.125,0.198 10 false 0 2,2.875 3.406,3.094 1.406,0.219 10 false Temperature (°C (°F)) 0.885,2.375 1.083,2.573 0.198,0.198 10 false 10 1.26,2.375 1.458,2.573 0.198,0.198 10 false 15 2.406,2.375 2.604,2.573 0.198,0.198 10 false 30 2.792,2.375 2.99,2.573 0.198,0.198 10 false 35 1.646,2.375 1.844,2.573 0.198,0.198 10 false 20 2.021,2.375 2.219,2.573 0.198,0.198 10 false 25 0.677,1.521 0.875,1.719 0.198,0.198 10 false 50 0.594,0.948 0.865,1.146 0.271,0.198 10 false 100 3.146,2.375 3.344,2.573 0.198,0.198 10 false 40 0.063,0.5 1.26,0.771 1.198,0.271 10 false Resistance (kΩ) 0.865,2.542 1.208,2.74 0.344,0.198 10 false (50) 1.229,2.552 1.573,2.75 0.344,0.198 10 false (59) 1.615,2.552 1.958,2.75 0.344,0.198 10 false (68) 1.979,2.563 2.323,2.76 0.344,0.198 10 false (77) 2.385,2.573 2.729,2.771 0.344,0.198 10 false (86) 2.771,2.583 3.115,2.781 0.344,0.198 10 false (95) 3.063,2.583 3.406,2.781 0.344,0.198 10 false (104)

The resistance of the thermistor built into the generator temperature sensor changes in accordance with changes in generator (MG1) temperature. The lower the generator (MG1) temperature, the higher the thermistor resistance. Conversely, the higher the generator (MG1) temperature, the lower the resistance.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A3611 Generator Temperature Sensor Circuit Short to Ground Short to ground in the generator temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU assembly

·

Generator temperature sensor (Hybrid vehicle transaxle assembly)


Comes on Master Warning Light:
Comes on
P0A3615 Generator Temperature Sensor Circuit Short to Auxiliary Battery or Open Open or short to +B in the generator temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU assembly

·

Generator temperature sensor (Hybrid vehicle transaxle assembly)


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0A3611 Generator Temperature
P0A3615

HINT:

After confirming that DTC P0A3611 or P0A3615 is output, use the GTS to check "Generator Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A407382E19
2.302,1.177 2.76,1.375 0.458,0.198 10 false 5 1.802,1.927 2.563,2.25 0.76,0.323 10 false GMTG 1.906,1.177 2.667,1.5 0.76,0.323 10 false GMT 2.302,1.927 2.76,2.125 0.458,0.198 10 false 4 0.292,2.677 1.052,3 0.76,0.323 10 false C65 0.302,2.844 2.208,3.604 1.906,0.76 10 false Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly) 2.552,2.667 4.563,3.521 2.01,0.854 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly Connector 2.563,2.521 3.323,2.844 0.76,0.323 10 false CA3 3.094,1.177 3.854,1.5 0.76,0.323 10 false 5 3.042,1.938 3.802,2.26 0.76,0.323 10 false 15 3.688,1.938 4.448,2.26 0.76,0.323 10 false 15 3.698,1.177 4.458,1.5 0.76,0.323 10 false 5 4.615,1.167 5.375,1.49 0.76,0.323 10 false 26 4.865,1.167 5.625,1.49 0.76,0.323 10 false GMT 4.635,1.927 5.396,2.25 0.76,0.323 10 false 27 4.875,1.917 5.635,2.24 0.76,0.323 10 false GMTG 4.948,2.688 5.708,3.01 0.76,0.323 10 false A28 4.938,2.833 6.646,3.51 1.708,0.677 10 false Hybrid Vehicle Control ECU Assembly 5.958,1.302 6.719,1.625 0.76,0.323 10 false ADC

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)
a.

Check that the intermediate connector which connects the generator temperature sensor to the hybrid vehicle control ECU is securely connected with no deformation, and that there is no contamination by water or foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

For vehicles in which the intermediate connector is inside the relay block, check for signs of water intrusion inside the relay block.


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connectors.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR TEMPERATURE SENSOR CONNECTOR)
a.
A407567E04
2.104,0.604 2.479,0.865 0.375,0.26 2.135,0.635 2.458,0.833 0.323,0.198 10 true C65

Check the connection condition of the generator temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.READ VALUE USING GTS (GENERATOR TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (GENERATOR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Generator Temperature.

Powertrain > Hybrid Control > Data List
Tester Display
Generator Temperature
50003 397 62

d.

Read the Data List.

Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)

B

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
a.
A407567E04
2.104,0.604 2.479,0.865 0.375,0.26 2.135,0.635 2.458,0.833 0.323,0.198 10 true C65

Disconnect the C65 generator temperature sensor connector.


b.
A385118C66
1.521,0.333 1.938,0.604 0.417,0.271 1.177,1.729 1.313,1.323 false 1.625,1.74 1.5,1.313 false 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 0.979,1.771 1.406,2 0.427,0.229 10 false GMT 1.438,1.771 1.865,2 0.427,0.229 10 false GMTG 1.604,0.375 2.063,0.573 0.458,0.198 10 false C65
*a Component without harness connected
(Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-5 (GMT) - C65-4 (GMTG) Power switch off 0.3338 to 1487 kΩ


HINT:

Terminal No. 3 on the component side connector is empty.



c.

Reconnect the C65 generator temperature sensor connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

6.INSPECT HYBRID VEHICLE CONTROL ECU ASSEMBLY
a.
A389500C81
0.552,0.833 1.052,1.083 0.5,0.25 0.417,2.5 0.583,1.854 true 1,2.5 0.646,1.854 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.167,2.542 0.729,2.708 0.563,0.167 10 false GMTG 0.906,2.531 1.469,2.698 0.563,0.167 10 false GMT 0.677,0.885 1.135,1.083 0.458,0.198 10 false A28
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)


Connect terminals 26 (GMT) and 27 (GMTG) of the A28 hybrid vehicle control ECU assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Generator Temperature.

Powertrain > Hybrid Control > Data List
Tester Display
Generator Temperature
50003 397 62

e.

Read the Data List.

OK:
GTS Display Condition Specified Condition
Generator Temperature Terminals A28-26 (GMT) and A28-27 (GMTG) connected
Power switch on (IG)
215°C (419°F)



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR TEMPERATURE SENSOR)
a.
A407567E04
2.104,0.604 2.479,0.865 0.375,0.26 2.135,0.635 2.458,0.833 0.323,0.198 10 true C65

Disconnect the C65 generator temperature sensor connector.


b.
A385118C66
1.521,0.333 1.938,0.604 0.417,0.271 1.177,1.729 1.313,1.323 false 1.625,1.74 1.5,1.313 false 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 0.979,1.771 1.406,2 0.427,0.229 10 false GMT 1.438,1.771 1.865,2 0.427,0.229 10 false GMTG 1.604,0.375 2.063,0.573 0.458,0.198 10 false C65
*a Component without harness connected
(Generator Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-5 (GMT) - C65-4 (GMTG) Power switch off 0.3338 to 1487 kΩ


HINT:

Terminal No. 3 on the component side connector is empty.



c.

Reconnect the C65 generator temperature sensor connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

8.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the C65 generator temperature sensor connector.


b.

Disconnect the A28 hybrid vehicle control ECU assembly connector.


c.
A407386C06
0.281,0.854 0.656,1.125 0.375,0.271 1.167,3.594 1.542,3.865 0.375,0.271 1.521,1.625 1.771,1.104 true 2.25,1.625 2.01,1.083 true 0.354,4.365 0.604,3.844 true 0.896,4.375 0.656,3.833 true 0.333,0.917 0.792,1.115 0.458,0.198 10 false C65 0.167,0.177 0.625,0.375 0.458,0.198 10 false *a 0.167,1.958 0.625,2.156 0.458,0.198 10 false *b 2.135,1.677 2.594,1.875 0.458,0.198 10 false GMT 1.333,1.677 1.938,1.906 0.604,0.229 10 false GMTG 1.219,3.677 1.677,3.875 0.458,0.198 10 false A28 0.865,4.417 1.469,4.646 0.604,0.229 10 false GMT 0.208,4.406 0.667,4.604 0.458,0.198 10 false GMTG
*a Front view of wire harness connector
(to Generator Temperature Sensor)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C65-5 (GMT) - A28-26 (GMT) Power switch off Below 1 Ω
C65-4 (GMTG) - A28-27 (GMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C65-5 (GMT) or A28-26 (GMT) - Body ground and other terminals Power switch off 10 kΩ or higher
C65-4 (GMTG) or A28-27 (GMTG) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A28 hybrid vehicle control ECU assembly connector.


e.

Reconnect the C65 generator temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR