Refer to the description for DTC P310711.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P310715 | Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open | Open or short to +B in the communication circuit
Communication from the airbag sensor assembly stopped and Circuit High has been detected for a certain period. (1 trip detection logic) |
·
Wire harness or connector ·
Airbag sensor assembly ·
Hybrid vehicle control ECU assembly |
Does not come on | Master Warning Light:
Comes on |
| DTC No. | Data List |
|---|---|
| P310715 | Airbag Status (Collision) |
After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 15 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Refer to the wiring diagram for DTC P310711.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Airbag system DTCs are not output. | A |
| Airbag system DTCs are output. | B |
Turn the power switch off.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Result | Proceed to |
|---|---|
| The waveform appears as shown in the illustration. | A |
| The waveform differs from the one shown in the illustration. | B |
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P310715 is not output. | A |
| P310715 is output again. | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Airbag sensor Assembly) |
Check the connector connections and contact pressure of the relevant terminals for the K73 airbag sensor assembly connector.
The connectors are connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K70 hybrid vehicle control ECU assembly connector.
Disconnect the K73 airbag sensor assembly connector.
Turn the power switch on (IG).
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-14 (ABFS) - Body ground | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the airbag sensor assembly connector and the hybrid vehicle control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-14 (ABFS) - K73-24 (GSW2) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-14 (ABFS) or K73-24 (GSW2) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the K73 airbag sensor assembly connector.
Reconnect the K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K73 airbag sensor assembly connector.
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU assembly) |
Measure the voltage according to the value(s) in the table below.
Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-14 (ABFS) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
Reconnect the K73 airbag sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K73 airbag sensor assembly connector.
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K73-33 (E1) - Body ground | Power switch off | Below 1 Ω |
Reconnect the K73 airbag sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG