Moving the shift lever to S enables the shift range to be selected. The shift range can be selected by operating the "+" or "-" shift paddle switch.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift UP Signal, Sports Shift DOWN Signal.
| Tester Display |
|---|
| Sports Shift UP Signal |
| Sports Shift DOWN Signal |
Read the values displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition |
|---|---|---|---|
| Sports Shift UP Signal | Sport shift up switch status | ON or OFF | Shift paddle switch RH (+) operated: ON
Shift paddle switch RH (+) not operated: OFF |
| Sports Shift DOWN Signal | Sport shift down switch status | ON or OFF | Shift paddle switch LH (-) operated: ON
Shift paddle switch LH (-) not operated: OFF |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the shift paddle switch (transmission shift switch assembly) operation | A |
| The GTS display does not change according to the shift paddle switch (transmission shift switch assembly) operation | B |
Turn the power switch off.
A
B
Disconnect the K70 hybrid vehicle control ECU assembly connector.
Disconnect the K29 transmission control switch (shift lock control unit assembly) connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the resistance according to the value(s) in the table below when the shift paddle switch (transmission shift switch assembly) is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-9 (SFTU) - Body ground | Shift paddle switch RH (+) operated | 3 Ω or less |
| K70-8 (SFTD) - Body ground | Shift paddle switch LH (-) operated | 3 Ω or less |
| K70-9 (SFTU) - Body ground | Shift paddle switch RH (+) not operated | 10 kΩ or higher |
| K70-8 (SFTD) - Body ground | Shift paddle switch LH (-) not operated | 10 kΩ or higher |
Reconnect the K29 transmission control switch (shift lock control unit assembly) connector.
Reconnect the K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Disconnect the K22 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-2 (ECC) - Body ground | Always | Below 1 Ω |
Reconnect the K22 spiral cable sub-assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K70 hybrid vehicle control ECU assembly connector.
Disconnect the K22 spiral cable with sensor sub-assembly connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
| *b | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-9 (SFTU) - K22-8 (SUP) | Always | Below 1 Ω |
| K70-8 (SFTD) - K22-1 (SDN) | Always | Below 1 Ω |
| K70-9 (SFTU) or K22-8 (SUP) - Body ground | Always | 10 kΩ or higher |
| K70-8 (SFTD) or K22-1 (SDN)- Body ground | Always | 10 kΩ or higher |
Reconnect the K22 spiral cable with sensor sub-assembly connector.
Reconnect the K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the shift paddle switch LH (transmission shift switch assembly).
Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the shift paddle switch RH (transmission shift switch assembly).
Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the z4 No. 1 switch wire connector.
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z4-2 (SUP) - z4-3 (ECC) | "+" (Up shift) shift paddle switch operated and held | Below 1 Ω |
| "+" (Up shift) shift paddle switch not operated | 10 kΩ or higher | |
| z4-4 (SDN) - z4-3 (ECC) | "-" (Down shift) shift paddle switch operated and held | Below 1 Ω |
| "-" (Down shift) shift paddle switch not operated | 10 kΩ or higher |
Reconnect the z4 No. 1 switch wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG