Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  Indicator Circuit  


DESCRIPTION

In accordance with the shift lever position, each shift position indicator light will turn on.

WIRING DIAGRAM

A396736E02
0.083,0.979 1.229,1.208 1.146,0.229 10 false from ACC Relay 1.417,1.177 2.49,1.375 1.073,0.198 10 false ECU-ACC 2.313,0.896 2.583,1.125 0.271,0.229 10 false 10 2.573,1.01 3.031,1.208 0.458,0.198 10 false PWR 3.594,1.021 3.75,1.219 0.156,0.198 10 false P 3.594,1.448 3.75,1.646 0.156,0.198 10 false R 3.594,1.875 3.75,2.094 0.156,0.219 10 false N 3.604,2.302 3.76,2.521 0.156,0.219 10 false D 3.604,2.729 3.76,2.948 0.156,0.219 10 false S 3.813,0.938 3.969,1.135 0.156,0.198 10 false 4 3.813,1.354 3.969,1.552 0.156,0.198 10 false 3 3.813,1.781 3.969,1.979 0.156,0.198 10 false 2 3.813,2.198 3.969,2.396 0.156,0.198 10 false 1 3.813,2.635 3.969,2.833 0.156,0.198 10 false 8 5.656,0.521 6.271,0.719 0.615,0.198 10 false ACCI 5.667,1.031 6.281,1.229 0.615,0.198 10 false INDP 5.667,1.458 6.281,1.656 0.615,0.198 10 false INDR 5.667,1.885 6.281,2.083 0.615,0.198 10 false INDN 5.677,2.313 6.292,2.51 0.615,0.198 10 false INDD 5.677,2.719 6.292,2.917 0.615,0.198 10 false INDM 5.333,0.333 5.646,0.531 0.313,0.198 10 false 22 5.333,0.844 5.646,1.042 0.313,0.198 10 false 13 5.375,1.271 5.688,1.469 0.313,0.198 10 false 8 5.333,1.688 5.646,1.885 0.313,0.198 10 false 12 5.333,2.115 5.646,2.313 0.313,0.198 10 false 11 5.333,2.531 5.646,2.729 0.313,0.198 10 false 10 5.281,0.521 5.74,0.719 0.458,0.198 10 false A28 5.292,1.042 5.906,1.24 0.615,0.198 10 false K70 5.292,1.469 5.906,1.667 0.615,0.198 10 false K69 5.292,1.885 5.906,2.083 0.615,0.198 10 false K70 5.292,2.313 5.906,2.51 0.615,0.198 10 false K70 5.292,2.729 5.906,2.927 0.615,0.198 10 false K70 2.51,3.219 2.823,3.417 0.313,0.198 10 false K79 2.5,3.375 4.229,3.688 1.729,0.313 10 false Shift Position Indicator 5.375,3.177 6.781,3.604 1.406,0.427 10 false Hybrid Vehicle Control ECU Assembly

PROCEDURE

1.CHECK SHIFT POSITION INDICATOR
a.

Turn the power switch on (ACC).


b.

Check that each shift position indicator light turns on correctly.

Result:
Result Proceed to
All shift position indicator lights turn on simultaneously A
Shift position indicator lights other than corresponding one turn on B
Corresponding shift position indicator light does not turn on C
No shift position indicator lights turn on D



c.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)

B

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)

C

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

D

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)
a.

Disconnect the K69 and K70 hybrid vehicle control ECU assembly connector.


b.
A389532C06
2.417,0.5 2.833,0.75 0.417,0.25 1.833,0.5 2.25,0.75 0.417,0.25 1.667,2.938 2.177,2.438 true 2.26,2.948 2.646,2.427 true 2.469,3.115 2.698,2.427 true 3.146,2.844 2.792,2.427 true 2.885,3.063 2.74,2.427 true 0.167,0.219 0.479,0.375 0.313,0.156 10 false *a 1.417,2.99 1.896,3.167 0.479,0.177 10 false INDR 2.031,2.979 2.469,3.198 0.438,0.219 10 false INDP 2.333,3.156 2.729,3.396 0.396,0.24 10 false INDN 2.771,3.156 3.167,3.375 0.396,0.219 10 false INDD 1.927,0.552 2.24,0.75 0.313,0.198 10 false K69 2.51,0.552 2.823,0.75 0.313,0.198 10 false K70 3.01,2.885 3.406,3.104 0.396,0.219 10 false INDM
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K70-13 (INDP) - Body ground and other terminals Always 10 kΩ or higher
K69-8 (INDR) - Body ground and other terminals Always 10 kΩ or higher
K70-12 (INDN) - Body ground and other terminals Always 10 kΩ or higher
K70-11 (INDD) - Body ground and other terminals Always 10 kΩ or higher
K70-10 (INDM) - Body ground and other terminals Always 10 kΩ or higher



c.

Reconnect the K69 and K70 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - SHIFT POSITION INDICATOR)
3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - SHIFT POSITION INDICATOR)
a.

Disconnect the K69 and K70 hybrid vehicle control ECU assembly connector.


b.

Disconnect the K79 shift position indicator connector.


c.
A406718C04
1.802,0.25 2.198,0.479 0.396,0.229 2.365,0.24 2.76,0.469 0.396,0.229 0.167,3.458 0.563,3.688 0.396,0.229 1.979,3.531 2.406,3.531 true 1.823,3.49 2.406,3.146 true 1.625,3.49 1.208,3.135 true 1.49,3.552 1.188,3.552 true 1.969,3.75 2.385,4.01 true 1.729,2.51 2.115,2.167 true 2.469,2.479 2.708,2.167 true 2.625,2.656 2.75,2.167 true 2.948,2.667 2.792,2.167 true 3.094,2.448 2.833,2.156 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 0.125,2.75 0.438,2.948 0.313,0.198 10 false *b 1.896,0.292 2.208,0.49 0.313,0.198 10 false K69 2.448,0.281 2.76,0.479 0.313,0.198 10 false K70 0.271,3.5 0.583,3.698 0.313,0.198 10 false K79 1.073,3.021 1.385,3.219 0.313,0.198 10 false N 1.052,3.49 1.365,3.688 0.313,0.198 10 false D 2.438,3.063 2.75,3.26 0.313,0.198 10 false R 2.458,3.458 2.771,3.656 0.313,0.198 10 false P 2.427,3.969 2.74,4.167 0.313,0.198 10 false S 2.99,2.49 3.406,2.708 0.417,0.219 10 false INDM 2.865,2.719 3.281,2.938 0.417,0.219 10 false INDD 2.49,2.719 2.906,2.938 0.417,0.219 10 false INDN 2.292,2.51 2.708,2.729 0.417,0.219 10 false INDP 1.438,2.51 1.854,2.729 0.417,0.219 10 false INDR
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Shift Position Indicator)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K70-13 (INDP) or K79-4 (P) - Body ground and other terminals Always 10 kΩ or higher
K69-8 (INDR) or K79-3 (R) - Body ground and other terminals Always 10 kΩ or higher
K70-12 (INDN) or K79-2 (N) - Body ground and other terminals Always 10 kΩ or higher
K70-11 (INDD) or K79-1 (D) - Body ground and other terminals Always 10 kΩ or higher
K70-10 (INDM) or K79-8 (S) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the K79 shift position indicator connector.


e.

Reconnect the K69 and K70 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the K79 shift position indicator connector.


b.

Turn the power switch on (ACC).


c.
A406717C03
0.333,0.865 0.792,1.156 0.458,0.292 2.063,1.5 2.531,1.646 true 0.448,0.927 0.906,1.125 0.458,0.198 10 false K79 0.115,0.094 0.573,0.292 0.458,0.198 10 false *a 2.583,1.625 3.042,1.823 0.458,0.198 10 false PWR
*a Front view of wire harness connector
(to Shift Position Indicator)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K79-10 (PWR) - Body ground Power switch on (ACC) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the K79 shift position indicator connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)
a.

Turn the power switch on (ACC).


b.
A321140C14
0.708,0.948 1.115,1.146 0.406,0.198 0.656,2.458 0.823,1.854 true 0.781,0.958 1.24,1.156 0.458,0.198 10 false A28 0.5,2.479 0.958,2.677 0.458,0.198 10 false ACCI 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-22 (ACCI) - Body ground Power switch on (ACC) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)
a.

Disconnect the K69 and K70 hybrid vehicle control ECU assembly connector.


b.

Turn the power switch on (ACC).


c.
A389532C06
2.417,0.5 2.833,0.75 0.417,0.25 1.833,0.5 2.25,0.75 0.417,0.25 1.667,2.938 2.177,2.438 true 2.26,2.948 2.646,2.427 true 2.469,3.115 2.698,2.427 true 3.146,2.844 2.792,2.427 true 2.885,3.063 2.74,2.427 true 0.167,0.219 0.479,0.375 0.313,0.156 10 false *a 1.417,2.99 1.896,3.167 0.479,0.177 10 false INDR 2.031,2.979 2.469,3.198 0.438,0.219 10 false INDP 2.333,3.156 2.729,3.396 0.396,0.24 10 false INDN 2.771,3.156 3.167,3.375 0.396,0.219 10 false INDD 1.927,0.552 2.24,0.75 0.313,0.198 10 false K69 2.51,0.552 2.823,0.75 0.313,0.198 10 false K70 3.01,2.885 3.406,3.104 0.396,0.219 10 false INDM
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K70-13 (INDP) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
K69-8 (INDR) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
K70-12 (INDN) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
K70-11 (INDD) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
K70-10 (INDM) - Body ground and other terminals Power switch on (ACC) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the K69 and K70 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - SHIFT POSITION INDICATOR)
7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - SHIFT POSITION INDICATOR)
a.

Disconnect the K69 and K70 hybrid vehicle control ECU assembly connector.


b.

Disconnect the K79 shift position indicator connector.


c.
A406718C05
1.802,0.25 2.198,0.479 0.396,0.229 2.365,0.24 2.76,0.469 0.396,0.229 0.167,3.458 0.563,3.688 0.396,0.229 1.979,3.531 2.406,3.531 true 1.823,3.49 2.406,3.146 true 1.625,3.49 1.208,3.135 true 1.49,3.552 1.188,3.552 true 1.969,3.75 2.385,4.01 true 1.729,2.51 2.115,2.167 true 2.469,2.479 2.708,2.167 true 2.625,2.656 2.75,2.167 true 2.948,2.667 2.792,2.167 true 3.094,2.448 2.833,2.156 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 0.125,2.75 0.438,2.948 0.313,0.198 10 false *b 1.896,0.292 2.208,0.49 0.313,0.198 10 false K69 2.448,0.281 2.76,0.479 0.313,0.198 10 false K70 0.25,3.5 0.563,3.698 0.313,0.198 10 false K79 1.073,3.021 1.385,3.219 0.313,0.198 10 false N 1.052,3.49 1.365,3.688 0.313,0.198 10 false D 2.438,3.063 2.75,3.26 0.313,0.198 10 false R 2.458,3.458 2.771,3.656 0.313,0.198 10 false P 2.427,3.969 2.74,4.167 0.313,0.198 10 false S 2.99,2.49 3.406,2.708 0.417,0.219 10 false INDM 2.865,2.719 3.281,2.938 0.417,0.219 10 false INDD 2.49,2.719 2.906,2.938 0.417,0.219 10 false INDN 2.292,2.51 2.708,2.729 0.417,0.219 10 false INDP 1.438,2.51 1.854,2.729 0.417,0.219 10 false INDR
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Shift Position Indicator)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K70-13 (INDP) - K79-4 (P) Always Below 1 Ω
K69-8 (INDR) - K79-3 (R) Always Below 1 Ω
K70-12 (INDN) - K79-2 (N) Always Below 1 Ω
K70-11 (INDD) - K79-1 (D) Always Below 1 Ω
K70-10 (INDM) - K79-8 (S) Always Below 1 Ω



d.

Reconnect the K79 shift position indicator connector.


e.

Reconnect the K69 and K70 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR