Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM (w/ Steering Control) › 2017.09–2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0331760 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the forward recognition camera.

WIRING DIAGRAM

A402116E01
0.375,0.906 3.438,1.104 3.063,0.198 10 false from IG1-NO. 1 Relay 2.677,1.063 4.667,1.26 1.99,0.198 10 false ECU-IG1 NO. 3 5.104,0.792 5.26,0.99 0.156,0.198 10 false 7 5.042,1.833 5.354,2.031 0.313,0.198 10 false 10 5.292,0.906 5.75,1.104 0.458,0.198 10 false IGB 5.281,1.958 5.74,2.156 0.458,0.198 10 false GND 4.802,2.479 5.115,2.677 0.313,0.198 10 false V6 4.802,2.635 6.688,2.854 1.885,0.219 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A380142C61
1.521,0.167 1.875,0.417 0.354,0.25 0.917,1.542 1.26,1.385 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.615,0.208 2.073,0.448 0.458,0.24 10 false V6 0.646,1.469 1.104,1.667 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the V6 forward recognition camera connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V6-7 (IGB) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
A380142C62
1.49,0.167 1.906,0.427 0.417,0.26 1.698,1.802 1.792,1.438 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.615,0.219 1.979,0.438 0.365,0.219 10 false V6 1.563,1.823 2.021,2.021 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the V6 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR