Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY (for Driver Side) › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331861 KNEE AIRBAG ASSEMBLY(for Driver Side) A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY(for Driver Side)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67914 4.REMOVE FRONT DOOR SCUFF PLATE

Hide 62112A 5.REMOVE COWL SIDE TRIM SUB-ASSEMBLY

Hide 62312B 6.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the instrument side panel.


Hide 55318C 7.REMOVE INSTRUMENT SIDE PANEL

Hide 55606 8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 55606 9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 55436B 10.REMOVE NO. 2 METER HOOD CLUSTER

Hide 53601 11.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55302D 12.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

Hide 55435B 13.REMOVE NO. 1 METER HOOD CLUSTER

Hide 55434B 14.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Hide 73900 15.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

CAUTION:
B417755C02
0.604,0.521 0.76,0.719 0.156,0.198 10 false .
V100155

Deployment Side


When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B490688

Remove the 4 bolts.


d.
B490689

Disengage the 2 claws and separate the lower No. 1 instrument panel airbag assembly.

NOTICE:

When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



e.
B490690C01
1.042,0.906 1.156,1.177 1.156,1.177 1.313,1.177 true 0.427,2.208 0.615,2.208 0.615,2.208 0.771,2.031 true 0.385,2.385 0.573,2.385 0.573,2.385 0.844,2.125 true 0.24,2.104 0.427,2.302 0.188,0.198 10 true *a 0.219,2.292 0.396,2.49 0.177,0.198 10 true *b 1.354,1.083 1.667,1.24 0.313,0.156 10 false *c
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Locking Button
V113147

Release in this Direction


Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.


f.

Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



Hide 73900 16.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)

CAUTION:
B417755C02
0.604,0.521 0.76,0.719 0.156,0.198 10 false .
V100155

Deployment Side


When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B474866

Remove the 4 bolts.


d.
B474867

Disengage the 2 claws and separate the lower No. 1 instrument panel airbag assembly.

NOTICE:

When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



e.
B474869C02
2.51,3.031 2.51,2.313 true 1.448,1.177 1.292,1.177 1.292,1.177 1.135,0.917 true 2.865,2.438 2.74,2.438 2.74,2.438 2.625,2.208 true 2.896,2.375 3.115,2.552 0.219,0.177 10 true *a 2.438,3.052 2.646,3.24 0.208,0.188 10 true *b 1.479,1.094 1.75,1.292 0.271,0.198 10 false *c
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Locking Button
V113147

Release in this Direction


Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.


f.

Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.